Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor
bcrowell
Posts: 90
Registered: ‎01-26-2011
Message 1 of 4 (351 Views)

Sliver trimming

351 Views, 3 Replies
07-13-2011 08:20 AM

A coworker is making a punch and is trying to trim the corners off of the model.  As of yet, we have tried subtraction extrusions, subtraction lofts, sweeps, etc to attempt to remove the material from the corners of this punch.  There is a small sliver between the outside curvature of the profile corner and just inside that profile.  It simply needs to be trimmed in that profile, normal to the flat surface of the punch.  He tried larger sketched geometry and it subtracted just fine, but it will not remove the sliver.

 

The part was originally derived with the mold, but some changes had to be made to the punch part to allow for the forming.  I have tried to compress the part enough to upload it , but have not been able to get it below 5MB so I have attached pictures.  They get progressively closer, zooming in to the small area in picture PUNCH3 between the red and blue line that we are trying to remove.

 

Any help would be appreciated.

 

We are running similar but not exactly the same computers, but use the same IV11 on Windows 7 Professional 64bit.

INV Professional 2015 (Build: 159, Release: 2015RTM), Windows 7 Professional (64-bit), SP1, Intel Xeon 3.07GHz CPU, 12GB RAM, NVIDIA Quadro 2000, Vault Basic 2015
*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 2 of 4 (329 Views)

Re: Sliver trimming

07-13-2011 10:26 AM in reply to: bcrowell

bcrowell wrote:

 

   I have tried to compress the part enough to upload it , but have not been able to get it below 5MB so I have attached pictures.  .

 

We are running similar but not exactly the same computers, but use the same IV11 on Windows 7 Professional 64bit.


Did you roll up the EOP before zipping to get the smallest filesize possible?
Find the red End of Part marker in the browser and drag to the top of the browser hiding all features from the graphics window.

Save the file with the EOP in a rolled up state.

In Windows Explorer right click on the filename and select Send to Compressed (zipped) Folder.
Is the resulting *.zip file still too large to attach here?

 

I can't really see the problem from the pictures - but my first thought is Delete Face with Heal option.

My second thought is to fix it in the Construction Environment.

 

Inventor 11 is a really old release and not supported as 64-bit - are you sure you aren't running Inventor 2011?

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
bcrowell
Posts: 90
Registered: ‎01-26-2011
Message 3 of 4 (301 Views)

Re: Sliver trimming

07-13-2011 11:09 AM in reply to: JDMather

Sorry, yes it is 2011.

 

Didn't know about rolling up the EOP before zipping- thank you.  Here it is.

 

The sketch geometry he is trying to use is in Sketch 17.

INV Professional 2015 (Build: 159, Release: 2015RTM), Windows 7 Professional (64-bit), SP1, Intel Xeon 3.07GHz CPU, 12GB RAM, NVIDIA Quadro 2000, Vault Basic 2015
*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 4 of 4 (289 Views)

Re: Sliver trimming

07-13-2011 12:29 PM in reply to: bcrowell

Well I took a quick look and didn't even get past the initial imported geometry.
It looks to my like it should be symmetrical but isn't.

And even if the design intent wasn't for symmetrical part - these faces still don't look good to me.
I would want to clean these up or get a clean model before going any further.

 

 

Edit: I healed the faces I was concerned about, shelled the 3.5 off and moved to origin.
see if anything can be done with attached.  (I got confused on what you are trying to trim off and the purpose of three consecutive Thickens of the same face.)

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.