Community
Inventor Forum
Welcome to Autodesk’s Inventor Forums. Share your knowledge, ask questions, and explore popular Inventor topics.
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Sheetmetal holes?

3 REPLIES 3
Reply
Message 1 of 4
Anonymous
162 Views, 3 Replies

Sheetmetal holes?

Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
selected at the same time and with the same diameter. How can I change the
diameter of only one of the holes? TIA, Bob
3 REPLIES 3
Message 2 of 4
Anonymous
in reply to: Anonymous

Rmb on the hole in the browser, and edit. Hold the control key and select
the one you want different to remove it from the rest that are selected. Ok
to finish the edit, then rmb on the sketch in the browser for the holes and
share it. Now add another hole using the point that you removed from the
other hole set.
--
Kent Keller
Member of the Autodesk Discussion Forum Moderator Program

http://www.MyMcad.com/KWiK/Mcad.htm

"Bob Johnson" wrote in message
news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYIadrTaRb...
> Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
> selected at the same time and with the same diameter. How can I change the
> diameter of only one of the holes? TIA, Bob
>
>
Message 3 of 4
Anonymous
in reply to: Anonymous

Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
key/select hole center point/OK, select hole tool, enter new hole size/OK?
Thanks again, Bob
"Kent Keller" wrote in message
news:88CEF94E0ADD9B27E6DFB81B296523DC@in.WebX.maYIadrTaRb...
> Rmb on the hole in the browser, and edit. Hold the control key and select
> the one you want different to remove it from the rest that are selected.
Ok
> to finish the edit, then rmb on the sketch in the browser for the holes
and
> share it. Now add another hole using the point that you removed from the
> other hole set.
> --
> Kent Keller
> Member of the Autodesk Discussion Forum Moderator Program
>
> http://www.MyMcad.com/KWiK/Mcad.htm
>
> "Bob Johnson" wrote in message
> news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYIadrTaRb...
> > Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern,
all
> > selected at the same time and with the same diameter. How can I change
the
> > diameter of only one of the holes? TIA, Bob
> >
> >
>
>
Message 4 of 4
Anonymous
in reply to: Anonymous

Not if I am following correctly (always suspect that I am not)

AFAIK you can not have two hole sizes on a sketch unless the sketch is shared. It sounds
to me like that is what you are trying to do. If you just share the sketch then
everything will be happy.

--
Kent
Member of the Autodesk Discussion Forum Moderator Program


"Bob Johnson" wrote in message
news:E607262317971A6A1E0E5AD969846BA2@in.WebX.maYIadrTaRb...
> Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
> key/select hole center point/OK, select hole tool, enter new hole size/OK?
> Thanks again, Bob

Can't find what you're looking for? Ask the community or share your knowledge.

Post to forums  

Autodesk Design & Make Report