Inventor General Discussion

Inventor General Discussion

Reply
Distinguished Contributor
tdswanson
Posts: 148
Registered: ‎03-07-2012
Message 1 of 8 (228 Views)

Secure Pin Component Generator - Can't Select End Plane?

228 Views, 7 Replies
01-17-2013 08:37 AM

Is anyone else having trouble with this DA?

 

When I try to create a pinned joint, I can't select the end plane for the vertical bar.  Am I missing something?  I've used this DA before, but it was quite some time ago and in IV2013.

 

Suggestions?  Thanks!

********************************************************
Inventor 2015 64-bit
Win 7 Pro 64-bit SP1
Contributor
scottph
Posts: 12
Registered: ‎01-17-2013
Message 2 of 8 (215 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-17-2013 10:06 AM in reply to: tdswanson

Hi,

 

I played with this for a while and I discovered that the end plane has to be on a different component than the original face that you select for the pin.  Looks like the pin would have to be able to go through that face as well.  I hope this helps.

 

Phillip

Distinguished Contributor
tdswanson
Posts: 148
Registered: ‎03-07-2012
Message 3 of 8 (208 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-17-2013 12:50 PM in reply to: scottph

Yes I figured that the end plane would have to be on a different component, but shouldn't I be able to select the plane that's the "seam" between the two parts?

 

In the example assembly that I attached, I can only select the end plane that's on the FAR side of the vertical bar, not the side that's really the mating face.

 

Thoughts?

********************************************************
Inventor 2015 64-bit
Win 7 Pro 64-bit SP1
Contributor
scottph
Posts: 12
Registered: ‎01-17-2013
Message 4 of 8 (203 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-17-2013 01:35 PM in reply to: tdswanson

I am speculating that the two faces you are trying to select would not cause the pin to go through both components.  If, for example, you are selecting the far positive Y direction face of dummy bar and the mating face, the pin and hole would not penetrate the base at all.  That is why the selection filter excludes it.

This is if I am understanding what you say, of course.

 

Phillip

Distinguished Contributor
tdswanson
Posts: 148
Registered: ‎03-07-2012
Message 5 of 8 (201 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-17-2013 01:45 PM in reply to: scottph

Were you able to get a pin inserted in the assembly I uploaded?

********************************************************
Inventor 2015 64-bit
Win 7 Pro 64-bit SP1
Contributor
scottph
Posts: 12
Registered: ‎01-17-2013
Message 6 of 8 (197 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-17-2013 02:25 PM in reply to: tdswanson

Yes, I was.  Unfortunately, though, I am working on 2014 beta, so you I can't send it to you.  I have zipped up a video, though.  Maybe that will help.

Distinguished Contributor
tdswanson
Posts: 148
Registered: ‎03-07-2012
Message 7 of 8 (185 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-18-2013 10:04 AM in reply to: scottph

OK, thanks very much for recording that.  However, that's not necessarily what I would call getting it to work....  Obviously in that example, I wouldn't be drilling a through hole clear from the other side.

 

Did this DA get broken during the 2012-2013 update? 

 

Paging Autodesk......  Can someone address this?

 

Thanks!

********************************************************
Inventor 2015 64-bit
Win 7 Pro 64-bit SP1
Contributor
scottph
Posts: 12
Registered: ‎01-17-2013
Message 8 of 8 (181 Views)

Re: Secure Pin Component Generator - Can't Select End Plane?

01-18-2013 10:45 AM in reply to: tdswanson

If you want to limit the depth of the hole you can use "By Hole" in the placement options, but you have to create a hole first.  Then you can select the mating face as the termination face.

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.