Inventor General Discussion

Inventor General Discussion

Reply
Distinguished Mentor
rdyson
Posts: 918
Registered: ‎04-11-2005
Message 1 of 8 (349 Views)
Accepted Solution

Section View Properties in iam

349 Views, 7 Replies
12-10-2012 12:57 PM

Using half / quarter section view, I know how to section CC parts.

How do I NOT section custom parts?

There has to be setting somewhere. Anyone know?

I guess you are looking for 'participate in assembly and drawing sections' you find this checkbox in the part environment

 

tools --> document settings --> modeling tab

 

i hope this helps!

 

Edit the part you don't want sectioned and uncheck this box in document settings.12-11-2012 8-58-00 AM.png

*Expert Elite*
Cadmanto
Posts: 3,356
Registered: ‎12-07-2011
Message 2 of 8 (343 Views)

Re: Section View Properties in iam

12-10-2012 01:32 PM in reply to: rdyson

You are talking about something similar to the Display Options under "Section Standard Parts" where you can select which groups you want sectioned except this in assembly mode I am assuming.

Or are you looking for something where you can randomly select individual parts that you don't want sectioned in the assembly model.

 

Either way I am not seeing anything that does this in the model.  If there is I would like to know myself as well.

Best Regards,
Scott McFadden
Inventor Professional 2014
(Colossians 3:23-25)

New Member
J.Pieters
Posts: 1
Registered: ‎12-10-2012
Message 3 of 8 (317 Views)

Re: Section View Properties in iam

12-10-2012 11:59 PM in reply to: rdyson

I guess you are looking for 'participate in assembly and drawing sections' you find this checkbox in the part environment

 

tools --> document settings --> modeling tab

 

i hope this helps!

 

Distinguished Mentor
rdyson
Posts: 918
Registered: ‎04-11-2005
Message 4 of 8 (303 Views)

Re: Section View Properties in iam

12-11-2012 06:44 AM in reply to: Cadmanto

Curtis,

There is obviously some setting that allows / causes CC parts to not participate in sectioning in the assembly environment. (see below)

I was looking for a way to make one of my parts behave the same.

 

Image1.png

Distinguished Mentor
john.retzlaff
Posts: 947
Registered: ‎11-03-2003
Message 5 of 8 (299 Views)

Re: Section View Properties in iam

12-11-2012 06:59 AM in reply to: rdyson

Edit the part you don't want sectioned and uncheck this box in document settings.12-11-2012 8-58-00 AM.png

John Retzlaff
Distinguished Mentor
rdyson
Posts: 918
Registered: ‎04-11-2005
Message 6 of 8 (291 Views)

Re: Section View Properties in iam

12-11-2012 09:21 AM in reply to: john.retzlaff

Thanks you! Knew it had to be somewhere.

*Expert Elite*
Cadmanto
Posts: 3,356
Registered: ‎12-07-2011
Message 7 of 8 (271 Views)

Re: Section View Properties in iam

12-11-2012 10:34 AM in reply to: john.retzlaff

John,

Thanks for the tip.

It is a shame that this is not built into the actual section command itself, like I have experienced in other softwares.

Where you can select components not to be affected while in the command.

Best Regards,
Scott McFadden
Inventor Professional 2014
(Colossians 3:23-25)

Distinguished Mentor
john.retzlaff
Posts: 947
Registered: ‎11-03-2003
Message 8 of 8 (268 Views)

Re: Section View Properties in iam

12-11-2012 10:35 AM in reply to: Cadmanto

Yes, sure would be nice if you could change this at the assembly level.

 

John Retzlaff
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.