Inventor General Discussion

Reply
*Dotson, Sean
Message 1 of 9 (76 Views)

Repeatable bug...now you try

76 Views, 8 Replies
11-05-2002 03:32 AM
RMB on a dimension in sketch mode in a part. Select Dimension Properties,
go to the Document settings tab and change Show Value to anything else and
hit OK. You should get Serious Error -Access Violation No RTTI data.

BTW the secret top getting out of the dialogue (since the cancel button
doesn't work) is to close the part with the x in the corner...

Hope this one makes it in SP1...(or is it just me?)

--
Sean Dotson, PE
http://www.sdotson.com
remove all #s from email
-----------------------------------------
*Mears, Brian
Message 2 of 9 (76 Views)

Re: Repeatable bug...now you try

11-05-2002 03:38 AM in reply to: *Dotson, Sean
I follow your directions and cannot reproduce the error. Works fine.


"Sean Dotson" wrote in message
news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> RMB on a dimension in sketch mode in a part. Select Dimension Properties,
> go to the Document settings tab and change Show Value to anything else and
> hit OK. You should get Serious Error -Access Violation No RTTI data.
>
> BTW the secret top getting out of the dialogue (since the cancel button
> doesn't work) is to close the part with the x in the corner...
>
> Hope this one makes it in SP1...(or is it just me?)
>
> --
> Sean Dotson, PE
> http://www.sdotson.com
> remove all #s from email
> -----------------------------------------
>
>
*Dotson, Sean
Message 3 of 9 (76 Views)

Re:

11-05-2002 03:46 AM in reply to: *Dotson, Sean
hmm.. after a reboot it's working fine now. However I did shut down and
retry it several times... strange...

Sorry for the alarm, nothing to see here, move along...

--
Sean Dotson, PE
http://www.sdotson.com
remove all #s from email
-----------------------------------------
"Brian Mears" wrote in message
news:CF608D4989BF16933479CB6C4A5A82F2@in.WebX.maYIadrTaRb...
> I follow your directions and cannot reproduce the error. Works fine.
>
>
> "Sean Dotson" wrote in message
> news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> > RMB on a dimension in sketch mode in a part. Select Dimension
Properties,
> > go to the Document settings tab and change Show Value to anything else
and
> > hit OK. You should get Serious Error -Access Violation No RTTI data.
> >
> > BTW the secret top getting out of the dialogue (since the cancel button
> > doesn't work) is to close the part with the x in the corner...
> >
> > Hope this one makes it in SP1...(or is it just me?)
> >
> > --
> > Sean Dotson, PE
> > http://www.sdotson.com
> > remove all #s from email
> > -----------------------------------------
> >
> >
>
>
*Jaquith, Walt
Message 4 of 9 (76 Views)

Re: Repeatable bug...now you try

11-05-2002 03:51 AM in reply to: *Dotson, Sean
Hi Sean,

Working in a simple little part sketch I created for the experiment (one
circle, one dim), I couldn't repeat your glitch. I also tried it on an
existing part and sketch. Nada.

WJ
*Allen, Albert
Message 5 of 9 (76 Views)

Re:

11-05-2002 03:54 AM in reply to: *Dotson, Sean
The force is strong with you Sean, I can sense it.
"Sean Dotson" wrote in message
news:ADE43998A291A42E94744B9BA9D18DCA@in.WebX.maYIadrTaRb...
> hmm.. after a reboot it's working fine now. However I did shut down and
> retry it several times... strange...
>
> Sorry for the alarm, nothing to see here, move along...
>
> --
> Sean Dotson, PE
> http://www.sdotson.com
> remove all #s from email
> -----------------------------------------
> "Brian Mears" wrote in message
> news:CF608D4989BF16933479CB6C4A5A82F2@in.WebX.maYIadrTaRb...
> > I follow your directions and cannot reproduce the error. Works fine.
> >
> >
> > "Sean Dotson" wrote in message
> > news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> > > RMB on a dimension in sketch mode in a part. Select Dimension
> Properties,
> > > go to the Document settings tab and change Show Value to anything else
> and
> > > hit OK. You should get Serious Error -Access Violation No RTTI data.
> > >
> > > BTW the secret top getting out of the dialogue (since the cancel
button
> > > doesn't work) is to close the part with the x in the corner...
> > >
> > > Hope this one makes it in SP1...(or is it just me?)
> > >
> > > --
> > > Sean Dotson, PE
> > > http://www.sdotson.com
> > > remove all #s from email
> > > -----------------------------------------
> > >
> > >
> >
> >
>
>
*Dotson, Sean
Message 6 of 9 (76 Views)

Re:

11-05-2002 03:56 AM in reply to: *Dotson, Sean
the "force" of stupidity?

--
Sean Dotson, PE
http://www.sdotson.com
remove all #s from email
-----------------------------------------
"Albert Allen" wrote in message
news:3D5E3DA025FE7D4382A94AF6D98F575A@in.WebX.maYIadrTaRb...
> The force is strong with you Sean, I can sense it.
> "Sean Dotson" wrote in message
> news:ADE43998A291A42E94744B9BA9D18DCA@in.WebX.maYIadrTaRb...
> > hmm.. after a reboot it's working fine now. However I did shut down and
> > retry it several times... strange...
> >
> > Sorry for the alarm, nothing to see here, move along...
> >
> > --
> > Sean Dotson, PE
> > http://www.sdotson.com
> > remove all #s from email
> > -----------------------------------------
> > "Brian Mears" wrote in message
> > news:CF608D4989BF16933479CB6C4A5A82F2@in.WebX.maYIadrTaRb...
> > > I follow your directions and cannot reproduce the error. Works fine.
> > >
> > >
> > > "Sean Dotson" wrote in message
> > > news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> > > > RMB on a dimension in sketch mode in a part. Select Dimension
> > Properties,
> > > > go to the Document settings tab and change Show Value to anything
else
> > and
> > > > hit OK. You should get Serious Error -Access Violation No RTTI
data.
> > > >
> > > > BTW the secret top getting out of the dialogue (since the cancel
> button
> > > > doesn't work) is to close the part with the x in the corner...
> > > >
> > > > Hope this one makes it in SP1...(or is it just me?)
> > > >
> > > > --
> > > > Sean Dotson, PE
> > > > http://www.sdotson.com
> > > > remove all #s from email
> > > > -----------------------------------------
> > > >
> > > >
> > >
> > >
> >
> >
>
>
*Keith_Bradford
Message 7 of 9 (76 Views)

Re:

11-05-2002 04:53 AM in reply to: *Dotson, Sean
Yes officer...

--
Keith Bradford
CAD Director
SCS/Frigette
817.293.5313
www.scsfrigette.com
(Remove All Numbers From E-mail)
"Sean Dotson" wrote in message
news:ADE43998A291A42E94744B9BA9D18DCA@in.WebX.maYIadrTaRb...
> hmm.. after a reboot it's working fine now. However I did shut down and
> retry it several times... strange...
>
> Sorry for the alarm, nothing to see here, move along...
>
> --
> Sean Dotson, PE
> http://www.sdotson.com
> remove all #s from email
> -----------------------------------------
> "Brian Mears" wrote in message
> news:CF608D4989BF16933479CB6C4A5A82F2@in.WebX.maYIadrTaRb...
> > I follow your directions and cannot reproduce the error. Works fine.
> >
> >
> > "Sean Dotson" wrote in message
> > news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> > > RMB on a dimension in sketch mode in a part. Select Dimension
> Properties,
> > > go to the Document settings tab and change Show Value to anything else
> and
> > > hit OK. You should get Serious Error -Access Violation No RTTI data.
> > >
> > > BTW the secret top getting out of the dialogue (since the cancel
button
> > > doesn't work) is to close the part with the x in the corner...
> > >
> > > Hope this one makes it in SP1...(or is it just me?)
> > >
> > > --
> > > Sean Dotson, PE
> > > http://www.sdotson.com
> > > remove all #s from email
> > > -----------------------------------------
> > >
> > >
> >
> >
>
>
*Autodesk, John Elliott -
Message 8 of 9 (76 Views)

Re: Repeatable bug...now you try

11-05-2002 07:07 AM in reply to: *Dotson, Sean
What OS are you using?

John
"Sean Dotson" wrote in message
news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> RMB on a dimension in sketch mode in a part. Select Dimension Properties,
> go to the Document settings tab and change Show Value to anything else and
> hit OK. You should get Serious Error -Access Violation No RTTI data.
>
> BTW the secret top getting out of the dialogue (since the cancel button
> doesn't work) is to close the part with the x in the corner...
>
> Hope this one makes it in SP1...(or is it just me?)
>
> --
> Sean Dotson, PE
> http://www.sdotson.com
> remove all #s from email
> -----------------------------------------
>
>
*Dotson, Sean
Message 9 of 9 (76 Views)

Re:

11-05-2002 09:50 PM in reply to: *Dotson, Sean
John, it seemed to fix itself after a reboot (see above) but if you are
still curious Win2K sp3

--
Sean Dotson, PE
http://www.sdotson.com
remove all #s from email
-----------------------------------------
"John Elliott - Autodesk" wrote in message
news:4468BBD9DEB523ED650D4D024F3C9CC9@in.WebX.maYIadrTaRb...
> What OS are you using?
>
> John
> "Sean Dotson" wrote in message
> news:690898FB90FF5764E2A2D1097BE7263D@in.WebX.maYIadrTaRb...
> > RMB on a dimension in sketch mode in a part. Select Dimension
Properties,
> > go to the Document settings tab and change Show Value to anything else
and
> > hit OK. You should get Serious Error -Access Violation No RTTI data.
> >
> > BTW the secret top getting out of the dialogue (since the cancel button
> > doesn't work) is to close the part with the x in the corner...
> >
> > Hope this one makes it in SP1...(or is it just me?)
> >
> > --
> > Sean Dotson, PE
> > http://www.sdotson.com
> > remove all #s from email
> > -----------------------------------------
> >
> >
>
>
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.