Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor
sam__gleeson
Posts: 58
Registered: ‎10-11-2012
Message 1 of 7 (326 Views)
Accepted Solution

part in sheet metal

326 Views, 6 Replies
11-23-2012 04:54 PM

Part attached is made from solid modelling.How can this part be made as a sheet metal part.....i`m not familiar yet with sheet metal....wanting to learn

Sam

INV 2013

Here you go.  Using Contour Flange is much quicker than doing it the conventional way.  But I notice in your model that the two bottom flanges are thicker than the rest of the model (3 instead of 2).  If that's really what you need, you can't do it in sheet metal (and I also wonder how it would be fabricated).

*Pro
sbixler
Posts: 1,968
Registered: ‎09-15-2003
Message 2 of 7 (298 Views)

Re: part in sheet metal

11-24-2012 07:08 PM in reply to: sam__gleeson

Here you go.  Using Contour Flange is much quicker than doing it the conventional way.  But I notice in your model that the two bottom flanges are thicker than the rest of the model (3 instead of 2).  If that's really what you need, you can't do it in sheet metal (and I also wonder how it would be fabricated).

Valued Contributor
sam__gleeson
Posts: 58
Registered: ‎10-11-2012
Message 3 of 7 (287 Views)

Re: part in sheet metal

11-25-2012 02:30 AM in reply to: sbixler

Hello Sam

 

Thanks alot.

 

Sam

*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 4 of 7 (275 Views)

Re: part in sheet metal

11-25-2012 07:04 AM in reply to: sam__gleeson

 

Thanks alot.

 


But his solution is incorrect for a sheet metal part.

 

Flat Pattern.PNG

 

 

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
sam__gleeson
Posts: 58
Registered: ‎10-11-2012
Message 5 of 7 (215 Views)

Re: part in sheet metal

11-26-2012 01:57 AM in reply to: sam__gleeson

OK JD...can you post your file then and i can then compare/see the differences

 

Thanks

 

Sam

*Pro
sbixler
Posts: 1,968
Registered: ‎09-15-2003
Message 6 of 7 (199 Views)

Re: part in sheet metal

11-26-2012 04:06 AM in reply to: sam__gleeson

JD's right, that my part is not correct-- but how you correct it depends on the design constraints.  If the edges that currently show as beveled in my part (and yours) are in contact with something else, then it matters whether the inside or outside edge is the correct dimension.  On the other hand, if the cutouts are just giving something else a wide clearance, then it's pretty easy to correct.  In any case, JD has done it properly for one of those cases, so maybe he'll post it.  Otherwise, tell us what the beveled edges' function is and I'll try to make it work for you.

*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 7 of 7 (190 Views)

Re: part in sheet metal

11-26-2012 05:01 AM in reply to: sam__gleeson

As indicated by Sam B the design intent for that corner where the angle crosses a bend is very important.

In the end you want a Flat Pattern where all of the edges are perpendicular to the flat.  This is easiest to check in wireframe shade mode.

 

Examine the attached file carefully in the bent angle corner for one possible solution.

 

 

Corner.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.