Inventor General Discussion

Inventor General Discussion

Reply
Member
mattfurches
Posts: 4
Registered: ‎05-21-2012
Message 1 of 9 (455 Views)
Accepted Solution

Origin and line midpoints not turning green

455 Views, 8 Replies
05-21-2012 08:15 PM

for some silly reason all of a sudden when i create a circle on the origin  it is not turning green and constraining the circle to it. Also when i am creating a line from the midpoint of another line the midpoint is not turning green and the line is not constrained to that point. Anybody have any ideas? I have checked the autoproject origin box in the appl settings and it is active.

*Expert Elite*
blair
Posts: 4,082
Registered: ‎11-13-2006
Message 2 of 9 (450 Views)

Re: Origin and line midpoints not turning green

05-21-2012 09:12 PM in reply to: mattfurches

Check that your Constraint Persistants and Constraint Inferance have not been turned off. Enter Sketch mode, from the Constraint drop-down menu make sure that they are selected.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up2 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Member
mattfurches
Posts: 4
Registered: ‎05-21-2012
Message 3 of 9 (440 Views)

Re: Origin and line midpoints not turning green

05-22-2012 04:44 AM in reply to: blair

i have checked the persistence and it is on. Anybody else?

Employee
patrick.miller
Posts: 99
Registered: ‎09-24-2008
Message 4 of 9 (436 Views)

Re: Origin and line midpoints not turning green

05-22-2012 05:03 AM in reply to: mattfurches

In the same "Constrain" pull-down, click Constraint Options and verify that coincident and midpoint are checked. 



Patrick Miller
Senior Content Developer
Autodesk, Inc.

Member
mattfurches
Posts: 4
Registered: ‎05-21-2012
Message 5 of 9 (433 Views)

Re: Origin and line midpoints not turning green

05-22-2012 05:11 AM in reply to: patrick.miller
In my constrain drop down box i dont have an options button.
*Expert Elite*
JDMather
Posts: 26,611
Registered: ‎04-20-2006
Message 6 of 9 (430 Views)

Re: Origin and line midpoints not turning green

05-22-2012 05:13 AM in reply to: mattfurches

While in sketch environment right click in the graphics window and select Constraint Options.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Mentor
trumpy81
Posts: 317
Registered: ‎10-22-2006
Message 7 of 9 (426 Views)

Re: Origin and line midpoints not turning green

05-22-2012 05:21 AM in reply to: mattfurches

Does the attached image help?

 

I have been having similar problems, but it is quite random and only seems to happen at certain zoom levels. Sometimes I'm able to attach to the midpoints etc... as per normal, and sometimes the mouse becomes a little erratic and I cannot always select the point or line directly.

 

Although the points usually do show and change color as expected.

Regards
Andy M
-------------------------------------------------------------------------------------------
Autodesk Inventor 2013 Pro SP1.1, Win7 Pro - 64Bit - SP1, Intel i7 960 @ 3.333 GHz
Asus X58 Sabertooth, Corsair 12Gig DDR3, AMD Radeon HD6970, Samsung 830 Series 256G SSD, 2x 3TB Seagate, 2x 2TB Hitachi,
1x 1TB Samsung, 4 x 2TB Seagate in Netgear ReadyNAS NV+, Dual Asus VE278Q Monitors
Member
mattfurches
Posts: 4
Registered: ‎05-21-2012
Message 8 of 9 (412 Views)

Re: Origin and line midpoints not turning green

05-22-2012 10:07 AM in reply to: trumpy81

it was the contraint options. for some unknown reason all the options had become unchecked. thanks for the help.

Active Member
k14348
Posts: 6
Registered: ‎05-22-2012
Message 9 of 9 (301 Views)

Re: Origin and line midpoints not turning green

11-16-2012 02:00 AM in reply to: mattfurches

right click --->constraint options ---->select all ----->apply.

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.