Inventor General Discussion

Inventor General Discussion

Reply
Active Member
bhn1981
Posts: 8
Registered: ‎06-12-2013
Message 1 of 9 (660 Views)

Missinng result window in Inventor Pro 2014 Stress Analysis

660 Views, 8 Replies
06-12-2013 11:42 AM

Hi.

 

When I perform an stress analysis, everything seems to work ok. Mesh is generated, and so on. The solution windows appear, and the progress bar runs from left to right. Then this window dissapear, as it should. In the model tree now, the result icon in the bottom of the tree, is shown, but no + ticker, that allow you to open the results. Also the Result and Display windows, on the upper panel bar, are grey, as if no analysis have been done.

 

Had this problem with inventor 2013 also, installed all hotfixes available, but didn't help. Now I have installed Inventor 2014, and also update 1, but still no change..

 

Anyone who know how this can be fixed?

 

Have been in contact with my local support, in Norway. And the haven't seen this before, and have no idea. 

 

Any ideas how to fix this will be highly appreciated..

 

Regards

Bjørn.

Distinguished Contributor
spackle42
Posts: 121
Registered: ‎05-12-2013
Message 2 of 9 (625 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

06-16-2013 08:32 PM in reply to: bhn1981

Hi Bjørn,

 

The best I can suggest is to have a look at your constraints.  I ran into this recently, never found a solution but once I scrapped my constraints and tried them another way, the problem disappeared.  My best guess is that the rule checker that makes sure the model is adequately setup misses one or two possibilities and so there's no error, it just fails during computation.  As always, if you can post a copy of your files, you'll probably get a more detailed answer from the bright sparks in here :-)

 

Regards,

 

 

Justin Smith



Justin Smith

Inventor Pro 2014 SP2
HP Z400 Workstation
Intel Xeon W3565 @ 3.20GHz
12Gb RAM
Win 7 64 Pro SP1
Spacepilot Pro v3.17.4
Active Member
bhn1981
Posts: 8
Registered: ‎06-12-2013
Message 3 of 9 (613 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

06-16-2013 11:12 PM in reply to: spackle42

Hi, and thanks for your reply.

All the constrains are ok, have tried with several simulations. So it is not just one part or assembly. If I open a part, that I have been working on, like 3 monts ago, it will open up, and show results ++, if I press the start simulation icon, the simulation for this part will, run, displaying results as normal. But if I eg. change the value of the applied force, then the simulation will fail. Have also tried to make a test part, from std inventor default part, but this doesn't help. similar result. Have deleted, and re-installed inventor, without this helping too. My version is fully licensed, and everything should be fine..

 

Regards

Bjorn

New Member
matt
Posts: 1
Registered: ‎05-02-2012
Message 4 of 9 (403 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

11-07-2013 03:28 AM in reply to: bhn1981

Hi

 

I have exactly the same problem. I have even tried the simulation on another computer and it works fine. 

Active Member
bhn1981
Posts: 8
Registered: ‎06-12-2013
Message 5 of 9 (398 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

11-07-2013 04:12 AM in reply to: bhn1981

Hi.

 

The only solution is to to a complete reinstallation of computer. Autodesk support tried "everything" with my software. I deleted inventor completely, removing all traces of autodesk without success. Did a complete reinstallation of autodesk packages twice, without success. Eventually they assumed it was something with windows registry files. All though this is a major task, involving reinstallation of everything on your computer, included windows, it solved all of my problems.. Of course it can be something else with your setup, but for me this was the only solution... unfortuneately..

 

rgds

Bjorn

New Member
Europafilter
Posts: 2
Registered: ‎01-19-2008
Message 6 of 9 (361 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

11-26-2013 04:13 AM in reply to: bhn1981

I also have a similar problem on Inventor 2014 W8 OS. 64Bit. The Stress analysis is greyed out. Tried to turn it on in the addin, restarted, open stress analysis and then all the choises are grey, not within reach. Removed Autodesk completely, re installed....same thing. I have heard that every second Windos OS is good /Bad. W7 was good....

Active Member
bhn1981
Posts: 8
Registered: ‎06-12-2013
Message 7 of 9 (354 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

11-26-2013 04:20 AM in reply to: Europafilter
Ligner på mitt problem, autodesk i Norge sin support klarte ikke å fikse dette, de kontakta også autodesk i usa uten at dei hadde andre ideer en å re installere pc. Har funket bra siden...
New Member
Europafilter
Posts: 2
Registered: ‎01-19-2008
Message 8 of 9 (352 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

11-26-2013 04:24 AM in reply to: bhn1981
W8 OS 64bit hos deg og?
Active Member
bhn1981
Posts: 8
Registered: ‎06-12-2013
Message 9 of 9 (350 Views)

Re: Missinng result window in Inventor Pro 2014 Stress Analysis

11-26-2013 04:26 AM in reply to: Europafilter
Nei, win 7 / 64 bit. Programmet fungerte heilt fint, så plutselig skjedde det et eller anna.. fungert fint siden..
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.