Inventor General Discussion

Inventor General Discussion

Reply
*Vit Votoupal
Message 1 of 8 (1,536 Views)

Lobsterback Pipe bend

1536 Views, 7 Replies
05-08-2008 03:51 PM
Would anybody has a ipart or just a model of large fabricated pipe bend
(lobster back). Sizes of pipes are 800mm & 1200mm.
Your help will be much appreciated.

--
vit votoupal » product development engineer » tna australia pty ltd » p +61
2 9714 2324 » m +61 041 215 2717 » f +61 2 9748 2970 »
vit.votoupal@tnasolutions.com» www.tnasolutions.com
*Expert Elite*
Inv_kaos
Posts: 728
Registered: ‎07-26-2007
Message 2 of 8 (1,536 Views)

Re: Lobsterback Pipe bend

05-08-2008 09:32 PM in reply to: *Vit Votoupal
Try this one. The number of segments include the two half segments at each end.

Regards,
Stew
Please mark as "Accept as Solution" if it answers your question or "Kudos" if you found it useful.
---------------------------------------------------------------------------------------------------------------------
Stew, AICP
Inventor Professional 2013, Autodesk Simulation Multiphysics 2013
Windows 7 x64 Core i7 32GB Ram FX2000
*Bob Stewart
Message 3 of 8 (1,536 Views)

Re: Lobsterback Pipe bend

05-09-2008 03:52 PM in reply to: *Vit Votoupal
You may want to check out this site:

http://www.inventor.jatsa.biz/DuctingItems.htm

HTH

Bob

"Vit Votoupal" wrote in message
news:5926606@discussion.autodesk.com...
Would anybody has a ipart or just a model of large fabricated pipe bend
(lobster back). Sizes of pipes are 800mm & 1200mm.
Your help will be much appreciated.

--
vit votoupal » product development engineer » tna australia pty ltd » p +61
2 9714 2324 » m +61 041 215 2717 » f +61 2 9748 2970 »
vit.votoupal@tnasolutions.com» www.tnasolutions.com
Distinguished Contributor
Raider_007
Posts: 484
Registered: ‎08-22-2006
Message 4 of 8 (1,533 Views)

Re: Lobsterback Pipe bend

06-07-2010 07:56 AM in reply to: *Bob Stewart

Hey also check out www.ductpro.net

Very nice tool!

 

Pieter

Contributor
Jsmith01
Posts: 11
Registered: ‎06-25-2010
Message 5 of 8 (1,456 Views)

Re: Lobsterback Pipe bend

06-25-2010 01:59 AM in reply to: Raider_007

Hi,

Duct Pro V1.2 is now available on the net. It supports Imperial inch units now. www.ductpro.net

 

J. Smith

Contributor
Jsmith01
Posts: 11
Registered: ‎06-25-2010
Message 6 of 8 (1,263 Views)

Re: Lobsterback Pipe bend

12-01-2010 01:20 PM in reply to: Jsmith01

Duct Pro for Inventor 2011 is now free.

Distinguished Mentor
IgorMir
Posts: 505
Registered: ‎08-02-2003
Message 7 of 8 (1,236 Views)

Re: Lobsterback Pipe bend

12-01-2010 03:11 PM in reply to: *Vit Votoupal

Here is one more alternative. To compliment other contributors suggestions.

Regards,

Igor.

Web: www.meqc.com.au
Contributor
Jsmith01
Posts: 11
Registered: ‎06-25-2010
Message 8 of 8 (1,180 Views)

Re: Lobsterback Pipe bend

12-08-2010 01:46 PM in reply to: IgorMir

Hey guys Duct Pro V2 is now available.

www.ductpro.net

 

Thanks

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.