Inventor General Discussion

Inventor General Discussion

Reply
Active Member
kenevens93
Posts: 7
Registered: ‎10-22-2012
Message 1 of 6 (397 Views)
Accepted Solution

Let a wheel roll in a randomly shaped rail

397 Views, 5 Replies
10-24-2012 09:31 AM

As you can see in the attachment (which is a small test version of my full project) do I have a problem..

 

The wheels on the side need to roll inside the guide rail. I can let them roll in each part separately but not in the entire rail.

I already tried with transitional constrains but then inventor says that there are some problems.

 

My project needs to become a sectional gate so there's going te be lots more than just 2 wheels in it...

 

Hope someone can explane me how to constrain this movement

Well, I guss you want to get  a animation, I prefer to use Inventor Dynamic Simulation to get such kind movement.

 

You can leverage the joint (sliding:Curve & Point), attached please fiind the iam file , I made some changes on your dataset, simpliified the assembly  and modified the guiderail part,  since it requires a close loop.

 

Inventor Professional 2013

Valued Mentor
mpatchus
Posts: 473
Registered: ‎10-22-2008
Message 2 of 6 (394 Views)

Re: Let a wheel roll in a randomly shaped rail

10-24-2012 09:38 AM in reply to: kenevens93

Try creating a continuous surface (as a seperate part) on the inside of the guide rails.

Constrain the wheels to this surface instead of the rails.

Turn the visibilty of the surface off as needed.

Mike Patchus

Inventor 2012 SP3 ~ Vault Pro 2013
==================
Lenovo D20 Workstation Intel Xenon E5640@2.67GHz (2)
Win 7, 24gb RAM, NVIDIA Quadro FX 3800

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below. :smileyhappy:
*Expert Elite*
mrattray
Posts: 2,501
Registered: ‎09-13-2011
Message 3 of 6 (390 Views)

Re: Let a wheel roll in a randomly shaped rail

10-24-2012 09:40 AM in reply to: kenevens93

Don't double post. It's bad karma..

 

hhttp://forums.autodesk.com/t5/Autodesk-Inventor/Constraining-to-a-random-path/td-p/3669326

Mike (not Matt) Rattray

Active Member
kenevens93
Posts: 7
Registered: ‎10-22-2012
Message 4 of 6 (386 Views)

Re: Let a wheel roll in a randomly shaped rail

10-24-2012 09:44 AM in reply to: kenevens93
I'm sorry but it did help... He gave me a good tip which i didn't get on the other post...

Mpatchus: The rail is made by sweeping along a continous axis but in the assembly it always gets divided.. How can i make a continuous surface that wont divided in the assembly?
Employee
jingyi.liu
Posts: 121
Registered: ‎08-28-2007
Message 5 of 6 (335 Views)

Re: Let a wheel roll in a randomly shaped rail

10-26-2012 01:22 AM in reply to: kenevens93

Well, I guss you want to get  a animation, I prefer to use Inventor Dynamic Simulation to get such kind movement.

 

You can leverage the joint (sliding:Curve & Point), attached please fiind the iam file , I made some changes on your dataset, simpliified the assembly  and modified the guiderail part,  since it requires a close loop.

 

Inventor Professional 2013

Inventor Professional 2015

Jingyi Liu
Quality Assurance Team
Autodesk
Employee
jingyi.liu
Posts: 121
Registered: ‎08-28-2007
Message 6 of 6 (330 Views)

Re: Let a wheel roll in a randomly shaped rail

10-26-2012 01:25 AM in reply to: kenevens93

Also modified attached part to create a sketch point.

Inventor Professional 2015

Jingyi Liu
Quality Assurance Team
Autodesk
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.