Inventor General Discussion

Inventor General Discussion

Reply
Contributor
Johnnyjack777
Posts: 13
Registered: ‎02-17-2011
Message 1 of 5 (529 Views)

Inventor Crashes on Simple Spline Extrude?

529 Views, 4 Replies
10-20-2012 08:27 PM

Curious... what the heck?

 

Crashes on a simple extrusion... VERY basic spline...

(When I click extrude... I doubt it's even a complete closed shape yet)

 

any thoughts?

Distinguished Mentor
Distinguished Mentor
wh
Posts: 592
Registered: ‎12-27-2003
Message 2 of 5 (517 Views)

Betreff: Inventor Crashes on Simple Spline Extrude?

10-20-2012 11:34 PM in reply to: Johnnyjack777

Set additional lines to construction lines, and it's ok.

 

Walter

*Expert Elite*
JDMather
Posts: 28,228
Registered: ‎04-20-2006
Message 3 of 5 (501 Views)

Re: Inventor Crashes on Simple Spline Extrude?

10-21-2012 07:41 AM in reply to: Johnnyjack777

Just took a look back through your previous posts here.
I don't see any improvement in your sketching techniques.
I recommed you read this document.

http://home.pct.edu/~jmather/AU2007/MA105-1L%20Mather.pdf

 

by this point you have probably developed bad habits that will be hard to break.

 

Find the Origin Center Point and use it.

Use Construction lines where appropriate (this was pointed out to you on an earlier problem).

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Employee
Yijiang.Cai
Posts: 359
Registered: ‎05-20-2008
Message 4 of 5 (475 Views)

Re: Inventor Crashes on Simple Spline Extrude?

10-21-2012 08:04 PM in reply to: Johnnyjack777

When using the dataset to extrude it, there is no crash seen. Maybe there are some key steps I missed. So could make more comments about the steps or workflow?

Thanks,
River Cai

Inventor Quality Assurance Team
Autodesk, Inc.
*Expert Elite*
JDMather
Posts: 28,228
Registered: ‎04-20-2006
Message 5 of 5 (445 Views)

Re: Inventor Crashes on Simple Spline Extrude?

10-22-2012 05:12 AM in reply to: Yijiang.Cai

Note that iProperties indicates the file is r2010 apparently with no Service Packs installed.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.