Inventor General Discussion

Reply
*DJSpaceMouse
Message 1 of 4 (50 Views)

Inventor 6 "Test Toolbars"

50 Views, 3 Replies
11-24-2002 10:59 PM
Has anyone enabled the test toolbars in Inventor 6? In prior releases, I've
seen an actual new toolbar (in the assembly environment, if I'm not
mistaken). After enabling it in Inventor 6, I didn't see another toolbar,
but after a while, I did finally see something new. Right-clicking on a
component in an assembly has another option - Segmentation, which can be set
to Fully Loaded or Unloaded. I haven't had the opportunity to really play
with this, but could it improve large-assembly performance by letting the
user manually load or unload data?
*Inc., Autodesk
Message 2 of 4 (50 Views)

Re: Inventor 6 "Test Toolbars"

11-24-2002 11:30 PM in reply to: *DJSpaceMouse
DJSpaceMouse wrote:

> Has anyone enabled the test toolbars in Inventor 6? In prior
> releases, I've
> seen an actual new toolbar (in the assembly environment, if I'm not
> mistaken). After enabling it in Inventor 6, I didn't see another toolbar,
> but after a while, I did finally see something new. Right-clicking on a
> component in an assembly has another option - Segmentation, which can
> be set
> to Fully Loaded or Unloaded. I haven't had the opportunity to really play
> with this, but could it improve large-assembly performance by letting the
> user manually load or unload data?
>
>
If this worked it would be in the product. These are unsupported tools
that may be toxic in your production environment.

-Kevin Schneider, Autodesk Inc.
*DJSpaceMouse
Message 3 of 4 (50 Views)

Re:

11-24-2002 11:36 PM in reply to: *DJSpaceMouse
Did I just stumble upon the Area 51 of Inventor? Are Autodesk's Men In
Black going to pay me a visit tonight? They're going to use that
mind-erasing pen of theirs on me, aren't they?

Anyone have Mulder's phone number handy?


"Kevin Schneider (Autodesk Inc.)" wrote in
message news:88B39E0AFB9252E62F0E602E94ADB2DD@in.WebX.maYIadrTaRb...
>
> If this worked it would be in the product. These are unsupported tools
> that may be toxic in your production environment.
>
> -Kevin Schneider, Autodesk Inc.
>
*Dotson, Sean
Message 4 of 4 (50 Views)

Re:

11-24-2002 11:52 PM in reply to: *DJSpaceMouse
There have been test toolbars in IV for most releases. As Kevin said
however a lot of the tools are not ready for prime time and can be
dangerous. I know I melted down an assembly back in R3 or 4 using some of
these tools...

--
Sean Dotson, PE
http://www.sdotson.com
...sleep is for the weak..
-----------------------------------------
"DJSpaceMouse" wrote in message
news:CF7C6A5639B6A498062B296F791240B6@in.WebX.maYIadrTaRb...
> Did I just stumble upon the Area 51 of Inventor? Are Autodesk's Men In
> Black going to pay me a visit tonight? They're going to use that
> mind-erasing pen of theirs on me, aren't they?
>
> Anyone have Mulder's phone number handy?
>
>
> "Kevin Schneider (Autodesk Inc.)" wrote in
> message news:88B39E0AFB9252E62F0E602E94ADB2DD@in.WebX.maYIadrTaRb...
> >
> > If this worked it would be in the product. These are unsupported tools
> > that may be toxic in your production environment.
> >
> > -Kevin Schneider, Autodesk Inc.
> >
>
>
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.