Inventor General Discussion

Reply
Member
jgodar
Posts: 4
Registered: ‎07-19-2011
Message 41 of 95 (1,023 Views)

Re: Inventor 2013 SP1

10-05-2012 09:18 AM in reply to: mrattray

Unfortunately SP1 is temporarily unavailable for download at this time.  We seem to be running ok at this time but will install as soon as available.

 

Thanks!

*Expert Elite*
mrattray
Posts: 2,507
Registered: ‎09-13-2011
Message 42 of 95 (1,020 Views)

Re: Inventor 2013 SP1

10-05-2012 09:20 AM in reply to: jgodar

I still have the installers for both 64bit and 32bit versions...

Mike (not Matt) Rattray

Valued Mentor
japike
Posts: 322
Registered: ‎02-06-2004
Message 43 of 95 (1,019 Views)

Re: Inventor 2013 SP1

10-05-2012 09:21 AM in reply to: mrattray

I've seen no perceptable increase speed or decrease in stability with SP1.

Peace,
Jeff
Inventor 2013
Distinguished Contributor
Ryan.Martinez
Posts: 141
Registered: ‎07-29-2011
Message 44 of 95 (1,014 Views)

Re: Inventor 2013 SP1

10-05-2012 09:23 AM in reply to: japike

IMO the beta service pack was more stable then the released one.

PDS 2014
PDS 2015
Board Manager
ChrisMitchell01
Posts: 414
Registered: ‎09-16-2005
Message 45 of 95 (990 Views)

Re: Inventor 2013 SP1

10-05-2012 10:24 AM in reply to: Ryan.Martinez

All,

 

A few comment to share:

 

  • The best way to really know what you have installed for any application, not just Inventor, is to look at Control panel, Add/Remove or Uninstall Programs & hit "View Installed updates"; this will show you all hotfixes, updates, SP's etc. (See attached) Many products only update their Help About major version when considerable changes are made, Eg with a major SP. Inventor 2013 will show build 138 if you have the release version, update1 or update2 installed. It will show build 170 SP1 if you installed the SP version. The "to be released" version will show SP1.1 with the final build number, (hopefully 176).

 

  • In so many cases with Inventor, because it is used in such diverse ways, everyone will likely have very different experiences with functionality, stability, performance, etc, etc as this thread shows. The memory management problem, that really caused SP1 to be taken down, considerably impacted many users, but not all, so some of you feel that build 170 is more stable than others do. We decided to err on the side of caution & fix the issue for everyone.

 

 

  • There will only be minimal code changes between build 170 & the "to be released" version so any performance improvements that were witnessed should still be there.

Hope this helps,

 

Thanks,
Chris



Chris Mitchell
Inventor Customer Engagement Team
Autodesk, Inc.

Distinguished Contributor
richiesuk
Posts: 227
Registered: ‎02-03-2009
Message 46 of 95 (770 Views)

Re: Inventor 2013 SP1

10-12-2012 03:57 AM in reply to: jgodar

any news regarding the date for downgrading update???

updatezzz providingzzzzzz

 

this is the most unstable INV so far...but is looks shiny ,hurray :womanindifferent:

 

Edited by
Discussion_Admin

*Expert Elite*
Mark_Wigan
Posts: 458
Registered: ‎03-07-2006
Message 47 of 95 (743 Views)

Re: Inventor 2013 SP1

10-12-2012 05:57 AM in reply to: richiesuk

Bearing in mind that we use this software to make a living is it too low brow to suggest autodesk pull their finger out and  take this software seriously...

 

spend some time on getting the basic stuff working properly and forget the shiny stuff until you get it right.  I would have thought AD would have learnt from their past oversights by now.

 

perhaps that is a bit harsh. I will apologise

 

tomorrow.

best regards,
- Mark

(Kudo or Tag if Solved - it may help others)

PDSU 2015 Windows 8.1, 64bit.

Employee
chucksavatsky
Posts: 13
Registered: ‎10-22-2007
Message 48 of 95 (686 Views)

Re: Inventor 2013 SP1

10-12-2012 12:52 PM in reply to: richiesuk

Hi,

 

We are currently on track for releasing an updated Inventor 2013 SP1 in mid October.  The expectation is that this will be made available some time next week.  I want to apologize for any inconvenience that this delay has caused.  Please know that we are working diligently to resolve the issues that were found in Inventor 2013 and doing everything possible to get these fixes made available as soon as possible.

 

Regards,

 

Chuck

Regards,

Chuck Savatsky
Director Software Development Inventor
Autodesk
Employee
chucksavatsky
Posts: 13
Registered: ‎10-22-2007
Message 49 of 95 (465 Views)

Re: Inventor 2013 SP1

10-16-2012 09:01 AM in reply to: jgodar

Hi,

 

Inventor 2013 SP1.1 has now been released.

It can be downloaded from http://usa.autodesk.com/adsk/servlet/ps/dl/item?siteID=123112&id=20442029&linkID=9242019.

 

 

Regards,

Chuck Savatsky
Director Software Development Inventor
Autodesk
Distinguished Contributor
richiesuk
Posts: 227
Registered: ‎02-03-2009
Message 50 of 95 (453 Views)

Re: Inventor 2013 SP1

10-16-2012 09:09 AM in reply to: jgodar

get ready Guinea Pigs :smileyvery-happy:

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.