Inventor General Discussion

Inventor General Discussion

Reply
Member
linelineline
Posts: 3
Registered: ‎05-11-2012
Message 1 of 5 (254 Views)
Accepted Solution

Inventor 2012 - Confused with angles.

254 Views, 4 Replies
05-11-2012 06:58 AM

Hi All,

 

I apologies in advance if I am asking stupid question but I am new to Inventor and I am confused about why I get different values of the same angle when I measure between two lines and between two surfaces? Please see attached angles.png.

 

angles.png

 

What I try to accomplish is as shown on detail.JPG

 

detail.JPG

 

but inventor 2012 do not let me constrain it properly(See the red oval that shows the problem) and seems like it thinks it is impossible. I just wonder if it is actually possible this and how should I constrain it with Inventor.

 

I have attached also the part and the assembly part and thanks in advance for your help.

 

Br, lien

*Expert Elite*
cwhetten
Posts: 1,072
Registered: ‎09-03-2008
Message 2 of 5 (227 Views)

Re: Inventor 2012 - Confused with angles.

05-11-2012 09:01 AM in reply to: linelineline

The answer to your first question about the difference in angle measurement is made clear by looking at the front ortho view of the part as you measure the angle.  The two measurements are not made in the same plane.  See the image: the red line is where the line-to-line measurement is made, and the blue line is the face-to-face measurement.

 

Angle Measure.png

 

I will take a look at the assembly for your second question.

*Expert Elite*
JDMather
Posts: 26,653
Registered: ‎04-20-2006
Message 3 of 5 (225 Views)

Re: Inventor 2012 - Confused with angles.

05-11-2012 09:02 AM in reply to: linelineline

Inventor is not confused.
I use a similar example of a crane frame in my class to demonstrate the true confusion.

 

First thing I noticed is that your Sketch1 is not constrained.  You might start here http://home.pct.edu/~jmather/skillsusa%20university.pdf  Make use of obvious symmetry.

 

Second thing I noticed is you are doing too much work - this is a simple problem.

 

Post back your next attempt and I will walk you through the solution if you haven't figured it out.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Member
linelineline
Posts: 3
Registered: ‎05-11-2012
Message 4 of 5 (194 Views)

Re: Inventor 2012 - Confused with angles.

05-11-2012 10:55 PM in reply to: JDMather

Thanks both,

 

Now is clear with the angles. Mr. Mather I have seen your tips and they are very useful.

 

I will try to follow your tips. I know the part seems overcomplecated but I have tried 5 different ways of doing it and never could make it work.

 

Br,

 

lien

Member
linelineline
Posts: 3
Registered: ‎05-11-2012
Message 5 of 5 (136 Views)

Re: Inventor 2012 - Confused with angles.

05-14-2012 11:00 PM in reply to: linelineline

Just for the record...

 

I was able to fix the problem. Thanks for your help. I followed the recommended tips. Also I understood what the problem was but not why this was a problem. If you see the picture bellow...

 

 

mate.jpg

 

After I removed the mate constrain shown on the picture above I was able to constrain as shown bellow

 

ok.JPG

 

Thanks again for your help and br,

 

lien

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.