Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor
88 Posts
11 Kudos
Registered: ‎07-15-2009
Post 1 of 11
Accepted Solution

inv 2012 isometric view when exiting sketch mode

1030 Views, 10 Replies
08-29-2011 06:48 AM

Sometimes when I'm exiting from a sketch, the entire model goes back to isometric view.  Is there a way to STOP this from happening?

 

Thank you

Sorry, you’re right.

 

I’ve discussed with our development.

 

This was an intentional change according to the user’s feedback.

 

When users tried to Extrude or Revolve while in a completely plan view, they did could not tell what to select.  By going to an ISO view, the users could see what they are doing.

 

There is no way to turn it off, but, it will only occur if the view is in a completely plan view. 

 

As it has been already suggested by cwhetten, if you orbit out of the plan view by just 1°, it will not go back to an ISO view.

 

Kind regards,

Alessandro

Product Support
333 Posts
176 Kudos
Registered: ‎06-10-2010
Post 2 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-29-2011 07:40 AM in reply to: chrisw01a

I hope you can find useful the post below.

http://forums.autodesk.com/t5/Autodesk-Inventor/Disable-Zoom-Home/m-p/3135110

 

Kind regards,

Alessandro



Alessandro Gasso
Product Support Technical Lead
MFG - Inventor
Autodesk, Inc.
Valued Contributor
88 Posts
11 Kudos
Registered: ‎07-15-2009
Post 3 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-29-2011 07:52 AM in reply to: alessandro.gasso

None of those ideas solved the problem.  I assume there is no solution...

Product Support
333 Posts
176 Kudos
Registered: ‎06-10-2010
Post 4 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-29-2011 08:02 AM in reply to: chrisw01a

Do you mean you don’t think it’s a good idea unchecking the option "Look at sketch plane on sketch creation" or that you still get the isometric view exiting from a sketch even without this option?

 

In the second case, can you provide a sample where this happens?

 

Thanks and regards,

Alessandro



Alessandro Gasso
Product Support Technical Lead
MFG - Inventor
Autodesk, Inc.
Valued Contributor
88 Posts
11 Kudos
Registered: ‎07-15-2009
Post 5 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-29-2011 09:36 AM in reply to: alessandro.gasso

I have no problem unchecking that option, actually, that is how I normally have it.

 

for one example, make a new part, with a new sketch, look at that sketch, and then exit the sketch.  The view returns to home.  (on mine)

 

I did uncheck the "fit to view on view change" on the cube, and I am liking that.

 

 

*Expert Elite*
1,104 Posts
269 Kudos
Registered: ‎09-03-2008
Post 6 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-29-2011 11:24 AM in reply to: chrisw01a

I have figured out a way to stop the Iso View on Exit Sketch.  Before I click the Exit Sketch command, I orbit the view slightly out-of-plane, then exit the sketch.  You have to orbit it out-of-plane, not just rotate the view about the axis normal to the view.  I hope that makes sense.

 

This works the same for 2011 and 2012.

 

-cwhetten

Valued Contributor
88 Posts
11 Kudos
Registered: ‎07-15-2009
Post 7 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-29-2011 12:16 PM in reply to: cwhetten

just don't understand why you would have to do this.  should be able to turn it off.

Product Support
333 Posts
176 Kudos
Registered: ‎06-10-2010
Post 8 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-30-2011 01:23 AM in reply to: chrisw01a

Sorry, you’re right.

 

I’ve discussed with our development.

 

This was an intentional change according to the user’s feedback.

 

When users tried to Extrude or Revolve while in a completely plan view, they did could not tell what to select.  By going to an ISO view, the users could see what they are doing.

 

There is no way to turn it off, but, it will only occur if the view is in a completely plan view. 

 

As it has been already suggested by cwhetten, if you orbit out of the plan view by just 1°, it will not go back to an ISO view.

 

Kind regards,

Alessandro



Alessandro Gasso
Product Support Technical Lead
MFG - Inventor
Autodesk, Inc.
Valued Contributor
88 Posts
11 Kudos
Registered: ‎07-15-2009
Post 9 of 11

Re: inv 2012 isometric view when exiting sketch mode

08-30-2011 04:50 AM in reply to: alessandro.gasso

Alright.  Thanks alot.  I know you can't please everybody.  Maybe the option will be available in 2013 :smileyhappy:

 

Take care.

Contributor
18 Posts
2 Kudos
Registered: ‎06-27-2003
Post 10 of 11

Re: inv 2012 isometric view when exiting sketch mode

12-29-2011 07:34 AM in reply to: alessandro.gasso

I have to agree with Chris on this: this should be a selectable option.

 

If I'm working in a cluttered model with lots of stuff going on, the last thing I want when exiting a sketch is for the whole thing to rotate away from where I've been working. Maybe the guys who want their sketch rotated for selection purposes should just rotate it, insead of requiring all those who don't want it rotated to rotate it a little to prevent it rotating a lot!

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are you interested in helping shape the future of the Autodesk Community? To participate in this brief usability study, please click here. Your time and input is greatly appreciated!