Inventor General Discussion

Inventor General Discussion

Reply
Active Member
JeremyEccleston
Posts: 6
Registered: ‎02-06-2012
Message 1 of 4 (239 Views)
Accepted Solution

Incremental dimensions with a minimum

239 Views, 3 Replies
04-10-2012 12:14 PM

I am new to Inventor and maybe biting off more than I can chew, but I am trying to set up a dimension that starts at a minimum value and increases incrementally by 1/16" of an inch to satisfy another dimension.  I've attached a pdf showing the part and the two dimensions.  I need the overall thickness of the part to start at 1 1/4" as shown and as the width (Depth + 1 1/2") changes, the thickness will grow when the tongue of the part gets less than 5/8".  I'm guessing this is an area best suited to ILogic, but I'm not sure how to get started.  Can anyone help, please?

Sorry forgot to post the video

http://video.answers.com/how-to-use-dimensions-in-autodesk-inventor-2011-299992420

 

How many different configurations will you have? You are making this an ipart right?

 

*Expert Elite*
mcgyvr
Posts: 7,101
Registered: ‎12-01-2004
Message 2 of 4 (228 Views)

Re: Incremental dimensions with a minimum

04-10-2012 12:50 PM in reply to: JeremyEccleston

You can do dimension equations/expressions in Inventor..

Watch this video.. Somewhere around the 2:45 second mark they start showing how to put equations/expressions into the dimension box..

Then

http://wikihelp.autodesk.com/Inventor/enu/2012/Help/0073-Autodesk73/0733-Design_O733/Functions%2c_pr...

 

 

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

-------------------------------------------------------------------------------------
2015 Product Design Suite Ultimate
Windows 7 64 bit
Core i7 4820k processor (OC'd to 4.4Ghz), Nvidia GTX 770, 16G RAM


Active Member
JeremyEccleston
Posts: 6
Registered: ‎02-06-2012
Message 3 of 4 (214 Views)

Re: Incremental dimensions with a minimum

04-10-2012 01:11 PM in reply to: mcgyvr

Thank you for looking at my question.  I'm not quite sure how to apply your suggestion.  I also don't see a video.  Maybe it's being blocked on our end, but normally there is a warning box that it was blocked.  I have an expression already in the one dimension field.  It is grabbing the "depth" dimension from another part and adding 1 1/2" to it.  I tried to do something like an IF/THEN statement that I would use in Excel, but that stayed red and would accept.  I also don't know how to make it adjust in 1/16" increments.  Maybe you could show me an example of what you're thinking?

*Expert Elite*
mcgyvr
Posts: 7,101
Registered: ‎12-01-2004
Message 4 of 4 (207 Views)

Re: Incremental dimensions with a minimum

04-10-2012 01:41 PM in reply to: JeremyEccleston

Sorry forgot to post the video

http://video.answers.com/how-to-use-dimensions-in-autodesk-inventor-2011-299992420

 

How many different configurations will you have? You are making this an ipart right?

 

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

-------------------------------------------------------------------------------------
2015 Product Design Suite Ultimate
Windows 7 64 bit
Core i7 4820k processor (OC'd to 4.4Ghz), Nvidia GTX 770, 16G RAM


Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.