Inventor General Discussion

Inventor General Discussion

Reply
Member
larzlorocks
Posts: 4
Registered: ‎06-18-2013
Message 1 of 4 (212 Views)
Accepted Solution

How to put a hole in a curved piece?

212 Views, 3 Replies
06-22-2013 07:35 PM

In the attached file I have a curved piece of sheet metal made with the contour flange tool. All I want to do is put a hole in the center of the sheet.

 

Thanks for your help!

You should post the version you are on, saves people downloading your file and producing a solution to your problem that you wouldn't be able to open and view.

 

Just create a work-plane from one straight end edge to the other. Project your side edges, create a construction line from middle side to middle side and place your circle center point on the middle of the line.

*Expert Elite*
blair
Posts: 4,155
Registered: ‎11-13-2006
Message 2 of 4 (206 Views)

Re: How to put a hole in a curved piece?

06-22-2013 08:37 PM in reply to: larzlorocks

You should post the version you are on, saves people downloading your file and producing a solution to your problem that you wouldn't be able to open and view.

 

Just create a work-plane from one straight end edge to the other. Project your side edges, create a construction line from middle side to middle side and place your circle center point on the middle of the line.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
*Expert Elite*
JDMather
Posts: 26,876
Registered: ‎04-20-2006
Message 3 of 4 (180 Views)

Re: How to put a hole in a curved piece?

06-23-2013 06:52 AM in reply to: larzlorocks

Actually, your question might be more complex than you realize (or than the "solution" Blair led you to).

 

There are more considerations on a sheet metal part.

Do you want the hole to be round in the flat or in the folded part (can't be both)?

When will the hole be made - before or after the part is rolled.

 

Usually the hole does not need to be perfectly round in the rolled part, so it is drilled or punched in the flat.

In that case, click Unfold (follow the prompts) create the Hole feature and then Refold.

 

If you need the hole to be perfectly round in the rolled part - it becomes just a bit more complex.
Again, when will the hole be added to the part.

If added in the flat stage it will not be circular - so will need to be punched, burnt or water-jet cut.

The easiest way to do in Inventor is to trim a surface and then Thicken/Offset.  This will also return the shape you need in the flat pattern.

 

A final option is the hole is made after rolling (in the actual manufacturing process - so no hole in the flat pattern).

If that is what you are after, post back for solution.

 

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Member
larzlorocks
Posts: 4
Registered: ‎06-18-2013
Message 4 of 4 (163 Views)

Re: How to put a hole in a curved piece?

06-23-2013 01:53 PM in reply to: JDMather

Huh, you're completely right. The hole will be made after the sheet is bent so that it is completely circular and will allow a cylinder to be put in. At this point the radius doesn't really matter.

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.