Inventor General Discussion

Inventor General Discussion

Reply
Member
Zenjashi
Posts: 3
Registered: ‎03-15-2011
Message 1 of 5 (1,431 Views)

How to make the cut in a drill bit?

1431 Views, 4 Replies
03-25-2011 06:02 AM
Hello Everyone,
I am drawing an adjustable drill stop. I have basically chamfered a cylinder to create a point. I know what the sweep profile looks like, I just cannot seem to angle the plane to be tangent with the chamfer. Any suggestions?

-Max

 

 

IV2011 Professional 32-Bit
*Expert Elite*
JDMather
Posts: 26,831
Registered: ‎04-20-2006
Message 2 of 5 (1,426 Views)

Re: How to make the cut in a drill bit?

03-25-2011 06:09 AM in reply to: Zenjashi

You title says cut a drill bit.
Description says a adjustable drill stop.

Can you provide pictures of similar real part?
I'm not sure what you are after.

Can you attach the ipt file here?

 

 

Did you get this problem sorted out http://forums.autodesk.com/t5/Autodesk-Inventor/Disobediance/m-p/2953006

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
Curtis_Waguespack
Posts: 2,930
Registered: ‎03-08-2006
Message 3 of 5 (1,401 Views)

Re: How to make the cut in a drill bit?

03-25-2011 06:37 AM in reply to: Zenjashi

Hi Zenjashi,

 

You can find an example of a drill bit profile in the practice drawing PDF on sheet 11 at this link:

http://inventortrenches.blogspot.com/2011/03/modeling-practice-drawings-for-inventor.html

 

You'll create the profile on the end of the shaft, and then use the Coil tool to cut the profile at the desired pitch and length. Then you can use the Circular Pattern tool and pattern the cut 2 times to complete the other side. You'll want to place the chamfer on the end after making the coil cuts.

 

If I have a chance I'll post an example later.

 

I hope this helps.

 

Best of luck to you in all of your Inventor pursuits,

Curtis

http://inventortrenches.blogspot.com/

 

 

 



  solution.png  Did you find this reply helpful ? If so please use the Accept as Solution or  Kudos button below.





*Expert Elite*
Curtis_Waguespack
Posts: 2,930
Registered: ‎03-08-2006
Message 4 of 5 (1,395 Views)

Re: How to make the cut in a drill bit?

03-25-2011 06:49 AM in reply to: Curtis_Waguespack

Hi Zenjashi,

 

Here is the part file to use as an example.

 

I hope it helps,

Curtis

http://inventortrenches.blogspot.com/

 

 

 



  solution.png  Did you find this reply helpful ? If so please use the Accept as Solution or  Kudos button below.





Valued Contributor
SORJM
Posts: 60
Registered: ‎05-01-2010
Message 5 of 5 (958 Views)

Re: How to make the cut in a drill bit?

05-06-2012 10:08 AM in reply to: Curtis_Waguespack
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.