Inventor General Discussion

Inventor General Discussion

Reply
Active Member
2shaen
Posts: 6
Registered: ‎11-04-2012
Message 1 of 7 (262 Views)
Accepted Solution

How to make marking

262 Views, 6 Replies
04-02-2013 01:32 AM

I have a part that is shaped like the attached. How to make a marking emboss on the red area?

Because before make a emboss i can't make sketch in area that.

thanks before...

*Expert Elite*
JDMather
Posts: 26,624
Registered: ‎04-20-2006
Message 2 of 7 (242 Views)

Re: How to make marking

04-02-2013 04:20 AM in reply to: 2shaen

Sketch1 is not constrained or making use of obvious symmetry about the origin.
I recommend you start here  http://home.pct.edu/~jmather/SkillsUSA%20University.pdf

 

Then you will want to make a plane tangent to your conical face for sketching the 2D to Emboss with Wrap to Face.

 

 

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Pro
sbixler
Posts: 1,885
Registered: ‎09-15-2003
Message 3 of 7 (236 Views)

Re: How to make marking

04-02-2013 04:50 AM in reply to: 2shaen

First, do what JDMather recommends above.  Then open the part I have attached, pull the End of Part marker down and examine how I did it.  This is not the only way, nor the "right" way, but it is robust and relatively easy to modify as needed.  Notice in sketch 1 that I did not need to divide all my diameter dimensions by two, but instead turned the axis to centerline type.  Dimensions placed to a centerline will automatically be placed as diameter dimensions.  I also used the Split tool with Trim Solid selected rather than the Sculpt tool.  Both tools give the correct result, but the Split tool is a bit more obvious to someone else looking at the file.

 

If you run into difficulties, post back here with your model attached.

Sam B
Inventor 2012 Certified Professional

Please click "Accept as Solution" if this response answers your question.
-------------------------------------------------------------------------------------
Inventor Professional 2013 SP1.1 Update 2
Windows 7 Enterprise 64-bit, SP1
HP EliteBook 8770w; 8 GB RAM; Core™ i7-3720QM 2.60 GHz; Quadro K4000M
SpaceExplorer/SpaceNavigator NB, driver 3.16.2
still waiting for a foreshortened radius dimensioning tool in Drawing Manager

Active Member
2shaen
Posts: 6
Registered: ‎11-04-2012
Message 4 of 7 (189 Views)

Re: How to make marking

04-02-2013 06:19 PM in reply to: JDMather

sorry i did not understand the tutorial. tutorial number how much should I use? could be more specific step by step.

 

Active Member
2shaen
Posts: 6
Registered: ‎11-04-2012
Message 5 of 7 (187 Views)

Re: How to make marking

04-02-2013 06:38 PM in reply to: sbixler

sorry can you explain how to rotate the plane. i attached picture that step.

*Pro
sbixler
Posts: 1,885
Registered: ‎09-15-2003
Message 6 of 7 (165 Views)

Re: How to make marking

04-03-2013 03:38 AM in reply to: 2shaen

Sketch2 contains the line where the angled face intersects the XY plane.  To create the tangent work plane, I selected the XY plane and the sketch line and left the default angle of 90°.  That is: Work Plane tool > select XY plane > select sketch line in Sketch2 > OK (to accept angle dimension 90°).

Sam B
Inventor 2012 Certified Professional

Please click "Accept as Solution" if this response answers your question.
-------------------------------------------------------------------------------------
Inventor Professional 2013 SP1.1 Update 2
Windows 7 Enterprise 64-bit, SP1
HP EliteBook 8770w; 8 GB RAM; Core™ i7-3720QM 2.60 GHz; Quadro K4000M
SpaceExplorer/SpaceNavigator NB, driver 3.16.2
still waiting for a foreshortened radius dimensioning tool in Drawing Manager

Active Member
2shaen
Posts: 6
Registered: ‎11-04-2012
Message 7 of 7 (140 Views)

Re: How to make marking

04-03-2013 07:07 PM in reply to: sbixler

thanks that tutorial is work...

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.