Inventor General Discussion

Inventor General Discussion

Reply
Active Contributor
32 Posts
1 Kudo
Registered: ‎01-11-2013
Post 1 of 8
Accepted Solution

How to make a coil

717 Views, 7 Replies
09-20-2013 05:26 AM

Hi boys,

 

I have a question, need help sure

 

How I would wrap/coil a tape around this attached picture?

You see the rounded edge, it's not fully circle

 

how to coil.PNG

HI!!

 

I dont have 2012 version installed.:smileyfrustrated:

 

I left you the browse three to help you following the construction of the coil.

The steps are described in JD post above.

 

 

 

*Expert Elite*
3,378 Posts
1,277 Kudos
Registered: ‎12-07-2011
Post 2 of 8

Re: How to make a coil

09-20-2013 07:03 AM in reply to: sohmoh

Check out this link and see if it helps you.

 

http://www.youtube.com/watch?v=q4htnkH2H1k

 

check.PNGIf this solved your issue please mark this posting "Accept as Solution".

Or if you like something that was said and it was helpful, Kudoskudos.PNG are appreciated. Thanks!!!! :smileyvery-happy:

 

New EE Logo.PNG

Inventor.PNG     vault.PNG

Best Regards,
Scott McFadden
Inventor Professional 2014
(Colossians 3:23-25)

Distinguished Mentor
991 Posts
242 Kudos
Registered: ‎02-04-2010
Post 3 of 8

Re: How to make a coil

09-20-2013 07:54 AM in reply to: sohmoh

Hi!

 

I d'ont know any tool to make this automatically.

 

Most of all, 2D and 3D sketches ... with a final sweep.

 

I made one manually, just for curiosity... it works well... see the file attached..

 

1.png

 

Note: You can went to the Parameters table and operate some changes.

 

Did you find this reply helpful ? If so, use the  Mark Solutions!  Accept as Solution or Give Kudos!Kudos - Thank you!

Regards.
CarlosC

Autodesk Inventor 2014 Certified Professional
Autodesk Factory Design Suite Ultimate 2015
Windows 7 64Bit
Active Contributor
32 Posts
1 Kudo
Registered: ‎01-11-2013
Post 4 of 8

Re: How to make a coil

09-21-2013 02:54 PM in reply to: ccarreiras

Hi Carlos,

 

YES.

 

It is exacly what I were looking for, Thank you very much.

But unfornitutly I couldn't open the ipt, I have Inventor 2012.

 

Could you please make it on IV2012.

 

Regards

Sohaib

Active Contributor
32 Posts
1 Kudo
Registered: ‎01-11-2013
Post 5 of 8

Re: How to make a coil

09-22-2013 02:41 AM in reply to: sohmoh

I forget to mention, the rectangular that I have its end not like his start.

Start with rectangular dimension for example 4 x3 but it end with smaler dimension for example 3 x 2.

 

How would the rectangular now folow the shape?

Sorry for this complexation 

 

 

Regards

Sohaib

*Expert Elite*
28,632 Posts
2,129 Kudos
Registered: ‎04-20-2006
Post 6 of 8

Re: How to make a coil

09-22-2013 04:45 AM in reply to: sohmoh

Loft or Extrude with taper the "tube" as a surface body (increase size by radius of swept feature).

Coil line as surface body.

3D sketch to find Intersection Sweep Path.

Workplane perpendicular to beginning of Sweep Path.

Create profile and Sweep.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Distinguished Mentor
991 Posts
242 Kudos
Registered: ‎02-04-2010
Post 7 of 8

Re: How to make a coil

09-25-2013 02:59 AM in reply to: sohmoh

HI!!

 

I dont have 2012 version installed.:smileyfrustrated:

 

I left you the browse three to help you following the construction of the coil.

The steps are described in JD post above.

 

 

 

Regards.
CarlosC

Autodesk Inventor 2014 Certified Professional
Autodesk Factory Design Suite Ultimate 2015
Windows 7 64Bit
Active Contributor
32 Posts
1 Kudo
Registered: ‎01-11-2013
Post 8 of 8

Re: How to make a coil

09-25-2013 09:15 AM in reply to: ccarreiras

Hi Carlos,

 

Thank you for your efforts and time. 

 

JD, Thank you too

 

Many thanks.

 

Regards

Sohaib

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are you interested in helping shape the future of the Autodesk Community? To participate in this brief usability study, please click here. Your time and input is greatly appreciated!