Inventor General Discussion

Inventor General Discussion

Reply
Contributor
DocGreen
Posts: 15
Registered: ‎01-29-2012
Message 1 of 9 (751 Views)

Flatten A Curved Plastic Part

751 Views, 8 Replies
11-23-2012 10:35 AM

Suppose we have a plastic part modeled as bent around a cylinder with an x-axis. Because the material is plastic and the manufacturing method is injection molding, part stretch is not a concern.

 

Suppose further that the part is a solid part that will be converted to a straight spring. The part needs to be flattened to obtain the correct spring dimensions--the part may have variable width in the x direction.

 

What is the best way to flatten this part?

*Expert Elite*
blair
Posts: 4,486
Registered: ‎11-13-2006
Message 2 of 9 (742 Views)

Re: Flatten A Curved Plastic Part

11-23-2012 11:54 AM in reply to: DocGreen

Follow the steps for the first two "Folds" but use 179.9 degrees (can't have it intersecting/colliding with itself) for each fold.

 

You will need to work out the material length that you require.

 

This was just an exercise to have  the holes in a flat pattern before bending, but the "Fold" principle is the same.

 

You really could increase the length of the base item and create a clamp with holes on the end flanges.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Contributor
DocGreen
Posts: 15
Registered: ‎01-29-2012
Message 3 of 9 (722 Views)

Re: Flatten A Curved Plastic Part

11-24-2012 12:06 AM in reply to: blair

I can't open the attachment:

 

   Database schema for file C:\Users\xxxxx\AppData\Local\Temp\Flange.ipt is (17.0 (Build 170095000, 95)), which is newer than this version (16.0 SP2 (Build 160219200, 219)) of the software

*Expert Elite*
blair
Posts: 4,486
Registered: ‎11-13-2006
Message 4 of 9 (696 Views)

Re: Flatten A Curved Plastic Part

11-24-2012 11:29 AM in reply to: DocGreen

It is done in IV2013, as noted in my post signature. The only way to get this into IV2012 is to export to a neutral format which would loose all the detail in the model tree.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Contributor
DocGreen
Posts: 15
Registered: ‎01-29-2012
Message 5 of 9 (694 Views)

Re: Flatten A Curved Plastic Part

11-24-2012 11:35 AM in reply to: blair

I'm taking the opportunity to update my installation to 2013.

*Expert Elite*
blair
Posts: 4,486
Registered: ‎11-13-2006
Message 6 of 9 (689 Views)

Re: Flatten A Curved Plastic Part

11-24-2012 11:46 AM in reply to: DocGreen

Install the SP1.1 as well.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Contributor
DocGreen
Posts: 15
Registered: ‎01-29-2012
Message 7 of 9 (674 Views)

Re: Flatten A Curved Plastic Part

11-24-2012 10:16 PM in reply to: blair

Now that I can see the part you posted, I think there is some miscommunication. I'm not trying to bend a part. Instead, I have a part modeled as bent around a constant curve -- cylinder around x-axis. What I need to do is straighten the part or unwrap surfaces so I can model the part as straight. I've read that others have had some success with using the sheet metal environment, but I'm hoping for a more direct and less klunky approach. The part has spline curves (as mentioned in the original description) that lead to variable width in the x direction and make ripping a shelled version of the part laborious.

 

I've attached two pictures. One shows the part shelled and gives a good example of the variable width I mentioned. The other is a side view showing the curves I want to straighten. Projecting from the curved surface to a 2D plane does not produce the desired result.

*Expert Elite*
blair
Posts: 4,486
Registered: ‎11-13-2006
Message 8 of 9 (668 Views)

Re: Flatten A Curved Plastic Part

11-24-2012 11:48 PM in reply to: DocGreen

Not as you have modeled it is it within the scope of Inventor. It could be done as Sheet-Metal in four pieces and then joined together to form an assembly (weldment) for the singe tube piece.

 

 

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Contributor
DocGreen
Posts: 15
Registered: ‎01-29-2012
Message 9 of 9 (654 Views)

Re: Flatten A Curved Plastic Part

11-25-2012 10:51 AM in reply to: blair

I was able to get the desired result as a flat pattern (see image with strategic use of SHELL. I've yet to find a way to convert the flat pattern into a 3D editable solid.

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.