Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor
rmorris
Posts: 65
Registered: ‎12-12-2003
Message 1 of 3 (31 Views)

Fastener Library Question

31 Views, 2 Replies
12-06-2002 02:32 AM
We are switching over to IV 6 SP1 from IV 5.3. We are trying to insert fasteners using the fastener library (I know iparts, we are heading that way) and when we use the same defined library that we used in 5.3 we get all kinds of errors. Do we need to define a new fastener library for 6? When I tried defining a new library it seemed to work fine. I just want to find out if we are going to have differnet libraries. We are not migrating all of our files right away. Just a couple of us are working on 6 for new projects.

Thanks in advance

Rob
IGC
*Keller, Kent
Message 2 of 3 (31 Views)

Re: Fastener Library Question

12-06-2002 03:10 AM in reply to: rmorris
In a assembly click on the word Model in the top of the browser and select library to get
to the R6 library. (hope I got that right going from memory )

--
Kent
Member of the Autodesk Discussion Forum Moderator Program


"rmorris" wrote in message news:f12a5b1.-1@WebX.maYIadrTaRb...
> We are switching over to IV 6 SP1 from IV 5.3. We are trying to insert fasteners using
the fastener library (I know iparts, we are heading that way) and when we use the same
defined library that we used in 5.3 we get all kinds of errors. Do we need to define a new
fastener library for 6? When I tried defining a new library it seemed to work fine. I just
want to find out if we are going to have differnet libraries. We are not migrating all of
our files right away. Just a couple of us are working on 6 for new projects.
> Thanks in advance
>
> Rob
> IGC
>
*J, Dave
Message 3 of 3 (31 Views)

Re:

12-06-2002 03:16 AM in reply to: rmorris
And make sure you uncheck "Load at Startup/Loaded". There have been problems
with old Library Content Add-In.

--
Dave Jacquemotte
davej@autoconcorp.com


"Kent Keller" wrote in message
news:BF4FE3A94913FB027EE1FCB3056D5DC5@in.WebX.maYIadrTaRb...
> In a assembly click on the word Model in the top of the browser and select
library to get
> to the R6 library. (hope I got that right going from memory )
>
> --
> Kent
> Member of the Autodesk Discussion Forum Moderator Program
>
>
> "rmorris" wrote in message
news:f12a5b1.-1@WebX.maYIadrTaRb...
> > We are switching over to IV 6 SP1 from IV 5.3. We are trying to insert
fasteners using
> the fastener library (I know iparts, we are heading that way) and when we use
the same
> defined library that we used in 5.3 we get all kinds of errors. Do we need to
define a new
> fastener library for 6? When I tried defining a new library it seemed to work
fine. I just
> want to find out if we are going to have differnet libraries. We are not
migrating all of
> our files right away. Just a couple of us are working on 6 for new projects.
> > Thanks in advance
> >
> > Rob
> > IGC
> >
>
>
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.