Inventor General Discussion

Reply
Active Member
raju
Posts: 8
Registered: ‎08-09-2004
Message 1 of 8 (492 Views)

Emboss in assembly

492 Views, 7 Replies
09-20-2012 03:15 PM

Is there a way I can use the emboss feature in an assembly?

 

We typically laser mark during final assembly and would like to show that as a step in the assembly instructions.

I typically create a sketch with the text and extrude(cut) in the assembly.

It works fine for flat surfaces, but cannot do it for other surfaces.

 

The one way I can think of doing it would be creating ipart with text and using it in the assembly.

I would rather not do it this way.  Is there any other way to accomplish this with out altering the components (.ipt)?

 

Thanks

 

Mentor
RobJV
Posts: 557
Registered: ‎07-14-2004
Message 2 of 8 (485 Views)

Re: Emboss in assembly

09-20-2012 03:44 PM in reply to: raju

Without fully understanding the problem, have you tried derived parts?

Active Member
raju
Posts: 8
Registered: ‎08-09-2004
Message 3 of 8 (448 Views)

Re: Emboss in assembly

09-22-2012 06:58 PM in reply to: raju

I know I can use derived parts, but want to avoid doing it.  I do not want to create any new parts.

Employee
stanislav.sedlak
Posts: 19
Registered: ‎12-08-2011
Message 4 of 8 (417 Views)

Re: Emboss in assembly

09-24-2012 03:34 AM in reply to: raju

Hi,

 

Unfortunately this is not supported currently. However there's a wishlist logged for this functionality #1458661.

 

Stanislav

*Expert Elite*
mrattray
Posts: 2,507
Registered: ‎09-13-2011
Message 5 of 8 (410 Views)

Re: Emboss in assembly

09-24-2012 04:59 AM in reply to: raju

I create a sketch in the flat pattern (I'm assuming sheetmetal) that I use for the actual laser programming, and in the drawing I use the retrieve model sketches command to show the etched lines.

Mike (not Matt) Rattray

Product Support
mercerc
Posts: 270
Registered: ‎10-29-2008
Message 6 of 8 (400 Views)

Re: Emboss in assembly

09-24-2012 07:41 AM in reply to: raju

            Although the emboss command is not available in the assembly features you can create a sketch in the assembly and place text in the sketch. Then you can extrude the text with a cut option. Not as many options as the emboss command but it will do what you want possibility.

Active Member
MadcapPomposity
Posts: 9
Registered: ‎02-22-2012
Message 7 of 8 (259 Views)

Re: Emboss in assembly

09-25-2013 08:01 AM in reply to: mercerc

I hadn't thought of using the Cut command on text, but I just tried it and it worked perfectly! You obviously can't get raised letters with Cut, but it engraves just as well as the Emboss command does.

Using:
Inventor 2013
AutoCAD 2013
Active Member
raju
Posts: 8
Registered: ‎08-09-2004
Message 8 of 8 (251 Views)

Re: Emboss in assembly

09-25-2013 08:39 AM in reply to: mercerc
Thank you.

Raju Penumatcha
Sr. Mechanical Engineer
raju.penumatcha@occfiber.com

[Description: OCC-Email-Sig-Logo]

1700 Capital Avenue, Suite 150
Plano, TX 75075
+1-972-509-1500 ext:108
Fax: +1-972-509-9009
occfiber.com

Connect with us...
Facebook | Twitter | LinkedIn
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.