Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 1 of 7 (532 Views)

curved bend in sheet metal part

532 Views, 6 Replies
12-26-2012 01:18 AM

Hi

 

Can a curved section with bend be applied to sheet metal part.I make extrusion for easier clarity.I am wanting to place the curved section (extrusion for demonstration purpose) with bend in sheet metal part but all created in the sheet metal environment.

 

Is this possible?

 

TC

*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 2 of 7 (516 Views)

Re: curved bend in sheet metal part

12-26-2012 04:53 AM in reply to: Terry__Close

Use Contour Roll.

I would do the rolled feature first.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 3 of 7 (487 Views)

Re: curved bend in sheet metal part

12-27-2012 04:10 AM in reply to: Terry__Close

OK

I did some searching and came up with the attempt attached.Have i done this correctly?

 

CAn this part now be flattened?

 

I do not use sheet metal that often but will make efforts to learn more

 

Terry

Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 4 of 7 (458 Views)

Re: curved bend in sheet metal part

12-28-2012 07:00 AM in reply to: Terry__Close

pls see attached

 

can this part be flattened?

*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 5 of 7 (433 Views)

Re: curved bend in sheet metal part

12-30-2012 06:09 AM in reply to: Terry__Close

I have not attempted your part yet, but after seeing your attempt I wish to revise my earlier statement.

Looks like if this is to work the Contour Roll should be created after the Face.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 6 of 7 (389 Views)

Re: curved bend in sheet metal part

01-01-2013 06:44 AM in reply to: Terry__Close

JD did you attempt to model this please.Would like to see correct solution

 

Terry

Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 7 of 7 (275 Views)

Re: curved bend in sheet metal part

01-08-2013 04:55 AM in reply to: Terry__Close

OK i have placed the Contour Roll after the face but still does not flatten.What am i doing wrong here?

 

Terry

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.