Inventor General Discussion

Inventor General Discussion

Reply
*Expert Elite*
JDMather
Posts: 28,262
Registered: ‎04-20-2006
Message 21 of 26 (225 Views)

Re: Copy/Paste Problem

10-03-2012 07:59 AM in reply to: JDMather

How is this assignment coming along?

I would have expected daily communication on this, given the due date and how little you had completed.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Contributor
JohnnyKash
Posts: 32
Registered: ‎08-12-2012
Message 22 of 26 (202 Views)

Re: Copy/Paste Problem

10-09-2012 04:38 PM in reply to: JDMather

Email notification didn't tell me about your last post.

 

I got it finished, mostly, yesterday. It's all modeled and put together as an assembly. I need to add the constraints that keep the parts from passing through one another, so it will act like a real mechanism. I haven't been able to figure out how to do that.

 

Is it possible for me to PM you with the file attached? I don't want someone appropriating it, given how many, many hours I've put into figuring out the correct proportions, angles, etc. of the mechanism. Hardest task I've ever done.   

Active Contributor
JohnnyKash
Posts: 32
Registered: ‎08-12-2012
Message 23 of 26 (177 Views)

Re: Copy/Paste Problem

10-10-2012 02:09 PM in reply to: JohnnyKash

Is it possible for me to PM the file to you? 

Active Contributor
JohnnyKash
Posts: 32
Registered: ‎08-12-2012
Message 24 of 26 (154 Views)

Re: Copy/Paste Problem

10-12-2012 03:22 PM in reply to: JDMather

See how the parts pass through one another? How do I constrain them so they will behave like real, solid matter and not do that?

 

[Edit] For some reason the file I attached isn't working. I'll figure it out and post again.

Active Contributor
JohnnyKash
Posts: 32
Registered: ‎08-12-2012
Message 25 of 26 (146 Views)

Re: Copy/Paste Problem

10-12-2012 04:03 PM in reply to: JDMather

Here it is.

 

[Edit] Well, no, it isn't. What do I need to do to the file so it will upload to here properly?

*Expert Elite*
JDMather
Posts: 28,262
Registered: ‎04-20-2006
Message 26 of 26 (138 Views)

Re: Copy/Paste Problem

10-12-2012 06:03 PM in reply to: JohnnyKash

An assembly file without parts is useless.

Drag the red End of Part marker to the top of the feature tree of any large files.
Save the file with the EOP in a rolled up state.

Right click on the filename and select Send to Compressed (zipped) Folder.
Attach the resulting *.zip files here.

 

Read about Contact Sets.

Read about Dynamic Simulation.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.