Inventor General Discussion

Reply
Distinguished Contributor
cadcamm99
Posts: 157
Registered: ‎04-12-2005
Message 1 of 10 (315 Views)

Constraint Dots

315 Views, 9 Replies
09-13-2012 09:59 AM

I have Inventor 2012.  When I work on a new model, I have the Yellow and Green dots when sketching. 

 

However if I work on an older model, the dots do not appear.  I have everything on. See attachments.  Not sure what else to check.

Distinguished Mentor
john.retzlaff
Posts: 934
Registered: ‎11-03-2003
Message 2 of 10 (300 Views)

Re: Constraint Dots

09-13-2012 10:53 AM in reply to: cadcamm99

On an existing sketch you will have to use show constraints to see the conincident constraints (yellow boxes).

 

John Retzlaff
*Expert Elite*
cbenner
Posts: 3,291
Registered: ‎04-06-2010
Message 3 of 10 (292 Views)

Re: Constraint Dots

09-13-2012 10:59 AM in reply to: john.retzlaff

Quick key to show Constraints is F8, just for reference.... F9 turns them off.

ChrisB

ADSK_Expert_Elite_Icon_S_Color_Blk.png

Please use Mark Solutions!.Accept as Solution &Give Kudos!Kudos to further enhance the value of these forums. Thank you! :smileyhappy:

http://cbennertipstricks.blogspot.com/


   

Distinguished Contributor
cadcamm99
Posts: 157
Registered: ‎04-12-2005
Message 4 of 10 (284 Views)

Re: Constraint Dots

09-13-2012 11:10 AM in reply to: cbenner

Actually didn't mean the grips.  I meant the yellow dot that follows the cursor and the green dot that shows up when your cursor is on an end point, midpoint or intersection point.

*Expert Elite*
mrattray
Posts: 2,506
Registered: ‎09-13-2011
Message 5 of 10 (265 Views)

Re: Constraint Dots

09-13-2012 12:26 PM in reply to: cadcamm99

Capture.JPG

Mike (not Matt) Rattray

*Pro
ampster
Posts: 1,271
Registered: ‎07-26-2005
Message 6 of 10 (257 Views)

Re: Constraint Dots

09-13-2012 12:30 PM in reply to: mrattray

OP's first pic shows those already set.

 

Just a guess since you mentioned older files, is it possible these files have not been fully migrated or saved up to the latest version you are using?

Distinguished Contributor
cadcamm99
Posts: 157
Registered: ‎04-12-2005
Message 7 of 10 (247 Views)

Re: Constraint Dots

09-13-2012 12:35 PM in reply to: cadcamm99

Turns out it is my part that is causing the problem.  After leaving Inventor and going back into it, things went back to normal.  However the more I worked with the part, it became progressivly unstable.  Not sure why part is doing that.

*Pro
ampster
Posts: 1,271
Registered: ‎07-26-2005
Message 8 of 10 (242 Views)

Re: Constraint Dots

09-13-2012 12:37 PM in reply to: cadcamm99

if possible, post your file/s here for others to look over.


I don't have 2012 myself, still on 2011 but maybe someone else can take a peek into your model and prehaps find something odd in there.

*Expert Elite*
mrattray
Posts: 2,506
Registered: ‎09-13-2011
Message 9 of 10 (237 Views)

Re: Constraint Dots

09-13-2012 12:49 PM in reply to: ampster

Oops, missed that.

Mike (not Matt) Rattray

Distinguished Mentor
john.retzlaff
Posts: 934
Registered: ‎11-03-2003
Message 10 of 10 (234 Views)

Re: Constraint Dots

09-13-2012 01:00 PM in reply to: cadcamm99

Have you done a rebuild on the part?

John Retzlaff
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.