Inventor General Discussion

Inventor General Discussion

Reply
Distinguished Contributor
cadcamm99
Posts: 161
Registered: ‎04-12-2005
Message 1 of 10 (343 Views)

Constraint Dots

343 Views, 9 Replies
09-13-2012 09:59 AM

I have Inventor 2012.  When I work on a new model, I have the Yellow and Green dots when sketching. 

 

However if I work on an older model, the dots do not appear.  I have everything on. See attachments.  Not sure what else to check.

Distinguished Mentor
john.retzlaff
Posts: 947
Registered: ‎11-03-2003
Message 2 of 10 (328 Views)

Re: Constraint Dots

09-13-2012 10:53 AM in reply to: cadcamm99

On an existing sketch you will have to use show constraints to see the conincident constraints (yellow boxes).

 

John Retzlaff
*Expert Elite*
cbenner
Posts: 3,421
Registered: ‎04-06-2010
Message 3 of 10 (320 Views)

Re: Constraint Dots

09-13-2012 10:59 AM in reply to: john.retzlaff

Quick key to show Constraints is F8, just for reference.... F9 turns them off.

ChrisB

ADSK_Expert_Elite_Icon_S_Color_Blk.png

Please use Mark Solutions!.Accept as Solution &Give Kudos!Kudos to further enhance the value of these forums. Thank you! :smileyhappy:

http://cadtipstricks.wordpress.com//


   

Distinguished Contributor
cadcamm99
Posts: 161
Registered: ‎04-12-2005
Message 4 of 10 (312 Views)

Re: Constraint Dots

09-13-2012 11:10 AM in reply to: cbenner

Actually didn't mean the grips.  I meant the yellow dot that follows the cursor and the green dot that shows up when your cursor is on an end point, midpoint or intersection point.

*Expert Elite*
mrattray
Posts: 2,538
Registered: ‎09-13-2011
Message 5 of 10 (293 Views)

Re: Constraint Dots

09-13-2012 12:26 PM in reply to: cadcamm99

Capture.JPG

Mike (not Matt) Rattray

*Pro
ampster
Posts: 1,388
Registered: ‎07-26-2005
Message 6 of 10 (285 Views)

Re: Constraint Dots

09-13-2012 12:30 PM in reply to: mrattray

OP's first pic shows those already set.

 

Just a guess since you mentioned older files, is it possible these files have not been fully migrated or saved up to the latest version you are using?

Distinguished Contributor
cadcamm99
Posts: 161
Registered: ‎04-12-2005
Message 7 of 10 (275 Views)

Re: Constraint Dots

09-13-2012 12:35 PM in reply to: cadcamm99

Turns out it is my part that is causing the problem.  After leaving Inventor and going back into it, things went back to normal.  However the more I worked with the part, it became progressivly unstable.  Not sure why part is doing that.

*Pro
ampster
Posts: 1,388
Registered: ‎07-26-2005
Message 8 of 10 (270 Views)

Re: Constraint Dots

09-13-2012 12:37 PM in reply to: cadcamm99

if possible, post your file/s here for others to look over.


I don't have 2012 myself, still on 2011 but maybe someone else can take a peek into your model and prehaps find something odd in there.

*Expert Elite*
mrattray
Posts: 2,538
Registered: ‎09-13-2011
Message 9 of 10 (265 Views)

Re: Constraint Dots

09-13-2012 12:49 PM in reply to: ampster

Oops, missed that.

Mike (not Matt) Rattray

Distinguished Mentor
john.retzlaff
Posts: 947
Registered: ‎11-03-2003
Message 10 of 10 (262 Views)

Re: Constraint Dots

09-13-2012 01:00 PM in reply to: cadcamm99

Have you done a rebuild on the part?

John Retzlaff
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.