Inventor General Discussion

Inventor General Discussion

Reply
Active Member
kenevens93
Posts: 7
Registered: ‎10-22-2012
Message 1 of 13 (405 Views)
Accepted Solution

Constraining to a random path

405 Views, 12 Replies
10-22-2012 10:19 AM

My goal is to let some wheels roll in a path which excist from 2 straight paths and a corner.

I can constrain them to 1 path at a time but not to all of them so my wheel makes a corner. I

 

You can find the guiderail as attachment. There is a path in the sketch from which i sweeped my form but he divides it in the 3 parts so i can't constrain the center point of my wheel to this path...

 

Can someone help me and give me some help.

 

Thanks a lot


kenevens93 wrote:

....divides it in the 3 parts so i can't constrain the center point of my wheel to this path...

 



Use Transitional constraint - not tangent.

I didn't see a wheel part file or an assembly file to demonstrate.

The track isn't grounded.

The wheels aren't constrained to the track.

 

A continuous surface can ge created through a trick of Delete face and then Patch (Boundary Patch).

 

But I think I would use Dynamic Simulation enviroment for this instead (works much better for motion like this).

 

To continue a discussion simply respond - bump.

*Expert Elite*
JDMather
Posts: 28,055
Registered: ‎04-20-2006
Message 2 of 13 (392 Views)

Re: Constraining to a random path

10-22-2012 11:48 AM in reply to: kenevens93

kenevens93 wrote:

....divides it in the 3 parts so i can't constrain the center point of my wheel to this path...

 



Use Transitional constraint - not tangent.

I didn't see a wheel part file or an assembly file to demonstrate.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Member
kenevens93
Posts: 7
Registered: ‎10-22-2012
Message 3 of 13 (387 Views)

Re: Constraining to a random path

10-22-2012 11:58 AM in reply to: JDMather

this is a wheel. But there need to beseveral wheels roll in this guide rail an they are attached to each other by a steel cable (the test assembly is without the attachement).

 

I've tried to work with the transitional but when all the wheels were constrained, he gave an error so nothing could move anymore..

 

Thanks for the fast reply

*Expert Elite*
JDMather
Posts: 28,055
Registered: ‎04-20-2006
Message 4 of 13 (367 Views)

Re: Constraining to a random path

10-22-2012 04:32 PM in reply to: kenevens93

You will need to add assembly constraints.

 

"when all the wheels were constrained"

I don't see any constraints.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Member
kenevens93
Posts: 7
Registered: ‎10-22-2012
Message 5 of 13 (337 Views)

Re: Constraining to a random path

10-23-2012 09:07 AM in reply to: JDMather

This is a test part of my full project so far. The names are in Dutch but you'll understand it right away because it's quite easy.

 

My problem is still the same. Letting the wheels roll inside the guide rail. There are only 2 now but in the end there will be 8 at each side so multiple panels can move like a sectional port at your garage.

 

Thanks by advance for your time.

 

*Expert Elite*
JDMather
Posts: 28,055
Registered: ‎04-20-2006
Message 6 of 13 (292 Views)

Re: Constraining to a random path

10-24-2012 10:02 AM in reply to: kenevens93

The track isn't grounded.

The wheels aren't constrained to the track.

 

A continuous surface can ge created through a trick of Delete face and then Patch (Boundary Patch).

 

But I think I would use Dynamic Simulation enviroment for this instead (works much better for motion like this).

 

To continue a discussion simply respond - bump.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
JDMather
Posts: 28,055
Registered: ‎04-20-2006
Message 7 of 13 (288 Views)

Re: Constraining to a random path

10-24-2012 10:04 AM in reply to: JDMather

To solve the problem - I recommend you concentrate on one panel at a time.  After you get the first one working (in DS) the rest will be easy.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
JDMather
Posts: 28,055
Registered: ‎04-20-2006
Message 8 of 13 (278 Views)

Re: Constraining to a random path

10-24-2012 10:14 AM in reply to: JDMather

There is no clearance between the wheels and the guidrail - both are 50mm?

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Member
kenevens93
Posts: 7
Registered: ‎10-22-2012
Message 9 of 13 (274 Views)

Re: Constraining to a random path

10-24-2012 10:17 AM in reply to: kenevens93
Yeah, I would normally change that but i first wont to know that its works like this
*Expert Elite*
JDMather
Posts: 28,055
Registered: ‎04-20-2006
Message 10 of 13 (270 Views)

Re: Constraining to a random path

10-24-2012 10:32 AM in reply to: kenevens93

Here is a trick to create a continuous surface with no seams.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are You Going To Be @ AU 2014? Feel free to drop by our AU topic post and share your plans, plug a class that you're teaching, or simply check out who else from the community might be in attendance. Ohh and don't forgot to stop by the Autodesk Help | Learn | Collaborate booths in the Exhibit Hall and meet our community team if you get a chance!