Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor
j_berry
Posts: 68
Registered: ‎11-15-2012
Message 1 of 5 (665 Views)
Accepted Solution

Chamfer set length

665 Views, 4 Replies
01-17-2013 01:59 PM

I searched and found numerous topics on this issue, all of them over 3 years old, so I guess it might be worth asking again.

 

I'm wondering if there is any way to chamfer a set length along an edge (similar to what can be done with flanges in sheet metal mode), as opposed to the entire length of an edge.

Hi j_berry,

 

You might have found this link in your searches, but if not there is an example file attached there that might help:

http://forums.autodesk.com/t5/Autodesk-Inventor/How-to-stop-chamfer-before-the-corner/m-p/3275375

 

And here is the link from that page that seems to have changed:

http://cadsetterout.com/inventor-tutorials/ifeature-stopped-chamfer/

 

You might also post your improvment idea to have an option to have it work like a sheet metal flange here:

Inventor IdeaStation

 

 

I hope this helps.
Best of luck to you in all of your Inventor pursuits,
Curtis
http://inventortrenches.blogspot.com

 

 

 

 

*Expert Elite*
Curtis_Waguespack
Posts: 3,000
Registered: ‎03-08-2006
Message 2 of 5 (663 Views)

Re: Chamfer set length

01-17-2013 02:08 PM in reply to: j_berry

Hi j_berry,

 

You might have found this link in your searches, but if not there is an example file attached there that might help:

http://forums.autodesk.com/t5/Autodesk-Inventor/How-to-stop-chamfer-before-the-corner/m-p/3275375

 

And here is the link from that page that seems to have changed:

http://cadsetterout.com/inventor-tutorials/ifeature-stopped-chamfer/

 

You might also post your improvment idea to have an option to have it work like a sheet metal flange here:

Inventor IdeaStation

 

 

I hope this helps.
Best of luck to you in all of your Inventor pursuits,
Curtis
http://inventortrenches.blogspot.com

 

 

 

 



  solution.png  Did you find this reply helpful ? If so please use the Accept as Solution or  Kudos button below.





*Expert Elite*
blair
Posts: 4,449
Registered: ‎11-13-2006
Message 3 of 5 (640 Views)

Re: Chamfer set length

01-17-2013 10:54 PM in reply to: j_berry

No, due to the nature of the fillet algorithim, it would know how to deal with the start and end face on the chamfer.

 

You would need to create a work plane and sketch using the Extrude-Cut

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Distinguished Contributor
VdVeek
Posts: 128
Registered: ‎09-13-2012
Message 4 of 5 (627 Views)

Re: Chamfer set length

01-18-2013 01:11 AM in reply to: blair

blair wrote:

No, due to the nature of the fillet algorithim, it would know how to deal with the start and end face on the chamfer.


Is the nature of a fillet algorithim different then a fillet? Because in a fillet it's posible. In the fillet option you can create a variable radius by placing points and change the radius to zero. Why not use this for a chamfer?

Rob.

Autodesk Inventor 2015 Certified Professional & Autodesk Inventor 2012 Certified Professional.
Valued Contributor
j_berry
Posts: 68
Registered: ‎11-15-2012
Message 5 of 5 (616 Views)

Re: Chamfer set length

01-18-2013 05:19 AM in reply to: Curtis_Waguespack

Curtis_Waguespack wrote:

Hi j_berry,

 

You might have found this link in your searches, but if not there is an example file attached there that might help:

http://forums.autodesk.com/t5/Autodesk-Inventor/How-to-stop-chamfer-before-the-corner/m-p/3275375

 

And here is the link from that page that seems to have changed:

http://cadsetterout.com/inventor-tutorials/ifeature-stopped-chamfer/

 

...

 


No, that topic had not come up in searches. A similar topic on that second link was exactly what I was looking for - the stopped chamfer with curved ends (Lark's tongue chamfer - http://cadsetterout.com/inventor-tutorials/ifeatures-larks-tongue-chamfer/ ). Thanks!

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.