Inventor General Discussion

Inventor General Discussion

Reply
Active Member
adavis
Posts: 8
Registered: ‎07-06-2011
Message 1 of 17 (1,294 Views)
Accepted Solution

Bending round bar

1294 Views, 16 Replies
08-29-2011 12:03 PM

Can you let me know if you can bend round bar from the content center or if I have to use a spine or loft command.  I have inventor premium and do not have the piping and tube option. 

 

thanks adria

*Expert Elite*
blair
Posts: 4,028
Registered: ‎11-13-2006
Message 2 of 17 (1,274 Views)

Re: Bending round bar

08-29-2011 01:17 PM in reply to: adavis

You should be able to use the "Bend"comand. You will need to create an Offset workplane tangent to the surface of the round bar. Create a Sketch, project the sides of the round bar, then create a line for your bend. You should then be able to bend the bar with the Bend command.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up2 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
*Expert Elite*
JDMather
Posts: 26,529
Registered: ‎04-20-2006
Message 3 of 17 (1,263 Views)

Re: Bending round bar

08-29-2011 01:37 PM in reply to: adavis

You can Bend any part.  Source doesn't matter.
Attach your file here.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Member
adavis
Posts: 8
Registered: ‎07-06-2011
Message 4 of 17 (1,231 Views)

Re: Bending round bar

08-30-2011 04:15 AM in reply to: blair

Thank you for your quick reply to my question.  I did try your solution earlier but it did not work.  I will try again maybe my work plane was not placed correctly. 

 

 

*Expert Elite*
JDMather
Posts: 26,529
Registered: ‎04-20-2006
Message 5 of 17 (1,219 Views)

Re: Bending round bar

08-30-2011 04:39 AM in reply to: adavis

Attach your file here.  I don't think you can place workplane "incorrectly" in such a way that Bend Part won't work.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
chrisw01a
Posts: 88
Registered: ‎07-15-2009
Message 6 of 17 (1,211 Views)

Re: Bending round bar

08-30-2011 05:02 AM in reply to: blair

I can't get this method to work either.  I drew up a 1" round x 10" long and put a tangent work plane and then drew a line perpendicular to the edges and you cannot select that line using the "bend" command.

 

 

*Expert Elite*
JDMather
Posts: 26,529
Registered: ‎04-20-2006
Message 7 of 17 (1,208 Views)

Re: Bending round bar

08-30-2011 05:04 AM in reply to: chrisw01a

chrisw01a wrote:

I can't get this method to work either.  I drew up a 1" round x 10" long and put a tangent work plane and then drew a line perpendicular to the edges and you cannot select that line using the "bend" command.

 

 


Attach the file here.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
chrisw01a
Posts: 88
Registered: ‎07-15-2009
Message 8 of 17 (1,198 Views)

Re: Bending round bar

08-30-2011 05:34 AM in reply to: JDMather

Here you go.

*Pro
sbixler
Posts: 1,880
Registered: ‎09-15-2003
Message 9 of 17 (1,189 Views)

Re: Bending round bar

08-30-2011 05:52 AM in reply to: chrisw01a

Your part is in the sheet metal environment, which is intended to work with uniform thickness materials (sheet metal, for instance).  The Bend tool is in the normal modeling environment, and if you change over to that environment, you will be able to bend your bar using the sketch you created.

Valued Contributor
chrisw01a
Posts: 88
Registered: ‎07-15-2009
Message 10 of 17 (1,181 Views)

Re: Bending round bar

08-30-2011 06:17 AM in reply to: sbixler

So it is.  I got it to bend.  Is there a way to "flatten" that out now for placement on a drawing showing the full length of the part then?

 

Thanks alot.

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.