Inventor General Discussion

Inventor General Discussion

Reply
New Member
fredw1444
Posts: 2
Registered: ‎04-19-2011
Message 1 of 3 (372 Views)
Accepted Solution

Bend Part, Bend Minimum, Example

372 Views, 2 Replies
10-13-2012 01:45 PM

I had a user ask about the Bend Minimum option of the Bend Part tool. I’ve looked at the Autodesk WikiHelp, full local Help, and various online resources, but have not been able to build an example part that will allow in me to see how the option works and I do not know what I’m missing. Does anyone have a sample part that demonstrates the Bend Minimum option or can you describe in more detail the conditions under which the option might be used?

 

The Help system entry for this option reads:

 

"Bend Minimum


When the Bend Line intersects multiple portions of the part body, use the Bend Minimum option to specify which portions are to be bent."

 

If you have a sample part you’d be willing to share with me, I’d love to see it.

 

Thanks,
Fred

You didn't specify which version of Inventor you are using, but I have attached a part (made in IV 2013) that may help you out.  This is an example from our Solid Modeling course that explains how the Bend Part command works.

 

As you can see in this picture, the L-shaped part has a 45 degree bend line on one leg, but the bend is also on the other leg.  The Bend line extends infinitely in both directions, and will bend (or attempt to bend) the part whenever it crosses it.

Bend1.png

 

If you toggle the Bend Minimum command, the part will only be bent along the selected visible line.

Bend2.png

 

If you have any other questions, feel free to ask!

Valued Contributor
JohnK_TEDCF
Posts: 72
Registered: ‎08-16-2010
Message 2 of 3 (365 Views)

Re: Bend Part, Bend Minimum, Example

10-13-2012 02:26 PM in reply to: fredw1444

You didn't specify which version of Inventor you are using, but I have attached a part (made in IV 2013) that may help you out.  This is an example from our Solid Modeling course that explains how the Bend Part command works.

 

As you can see in this picture, the L-shaped part has a 45 degree bend line on one leg, but the bend is also on the other leg.  The Bend line extends infinitely in both directions, and will bend (or attempt to bend) the part whenever it crosses it.

Bend1.png

 

If you toggle the Bend Minimum command, the part will only be bent along the selected visible line.

Bend2.png

 

If you have any other questions, feel free to ask!

John Koop
Software Engineer/ Inventor Specialist
TEDCF Publishing
www.trainingtutorial.com
New Member
fredw1444
Posts: 2
Registered: ‎04-19-2011
Message 3 of 3 (336 Views)

Re: Bend Part, Bend Minimum, Example

10-14-2012 11:54 AM in reply to: JohnK_TEDCF

John,

 

Thanks for the reply. I’m running 2012 SP2 at the office, which is where the question came up.  I created a 2012 version of your sample and was able to get the model to behave as depicted in your graphic. I created a sample in 2012 that looked more like a fork pointing upward and I drew a horizontal bend line across one of the tines. The model did not behave as the user and I expected.

 

I’ve worked with the TEDCF material in the past. I’ll give it another look.

 

Thank you very much,

Fred

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.