Inventor General Discussion

Inventor General Discussion

Reply
Distinguished Contributor
lis_wang
Posts: 433
Registered: ‎11-26-2003
Message 1 of 19 (881 Views)
Accepted Solution

ball pattern in BALL SCREW assembly

881 Views, 18 Replies
10-18-2012 12:33 AM

May I know how to pattern the ball in BALL SCREW assembly? The ball screw assembly is attached.

 

Thanks

Distinguished Contributor
lis_wang
Posts: 433
Registered: ‎11-26-2003
Message 2 of 19 (882 Views)

ball pattern in BALL SCREW assembly

10-18-2012 12:34 AM in reply to: lis_wang

May I know how to pattern the ball in BALL SCREW assembly? The ball screw assembly is attached.

 

As the file is big, so I posted here in two messages.

 

Thanks

*Expert Elite*
JDMather
Posts: 26,651
Registered: ‎04-20-2006
Message 3 of 19 (858 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 05:29 AM in reply to: lis_wang

Really it depends on what you want to do with this.

 

The easiest solution is a curve driven pattern of Workpoints in the screw part and then use that pattern to place the balls in the assembly.

 

If your end goal is Dynamic Simulation then a bit more work is required.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Distinguished Contributor
lis_wang
Posts: 433
Registered: ‎11-26-2003
Message 4 of 19 (850 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 06:17 AM in reply to: JDMather

I do not undertand what you said. Could you please pattern the ball inside the nut. I do not do the Dynamic Simulation.

 

Thanks

*Expert Elite*
JDMather
Posts: 26,651
Registered: ‎04-20-2006
Message 5 of 19 (837 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 06:44 AM in reply to: lis_wang

See Tips 43-47 here http://home.pct.edu/~jmather/SkillsUSA%20University.pdf

 

and also

 

the slot and the ball are the same size (no allowance for clearance and manufacturing tolerance) - we can't make perfect parts in the real world.

 

and also

 

the circle sketch for the coil is not perpendicular to the start of the helix - therefore the slot is not round in cross-section and there is interference between the ball and the screw and nut.

 

Start with a Natural start condition (off the end of the part far enough that only the helix is cut or use a single line Coil to create a surface body coil to use with Sweep.  This will be needed to place and pattern the WorkPoints, so that is how I would do the part.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
JDMather
Posts: 26,651
Registered: ‎04-20-2006
Message 6 of 19 (832 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 06:52 AM in reply to: JDMather

The blue "line" is your circle profile on edge view.
The purple curve is the Helix.

Notice that the blue line is not perpendicular to the start of the helix.

The orange "line" is a Workplane created perpendicular to the start of the helix.

 

very few people catch this mistake that results in incorrect geometry.

Helix Curve.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Distinguished Contributor
lis_wang
Posts: 433
Registered: ‎11-26-2003
Message 7 of 19 (826 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 07:14 AM in reply to: JDMather

I do not get what your mean. Is that possible give me the file, I take a look myself?

 

Thanks

*Expert Elite*
JDMather
Posts: 26,651
Registered: ‎04-20-2006
Message 8 of 19 (820 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 07:35 AM in reply to: lis_wang

I am using 2013 - so you would not be able to open my file even if I posted it.

 

In this image there are two circles - the 6mm circle you used with Coil to cut the face shown in orange.

I cut back overtop that feature (red) with a 5.99mm circle and notice that it cuts the sides more even though the circle is smaller.

My circle is perpendicular to the helix, yours is not.

 

I made a mistake earlier when I said one solution was Natural on the start of the Coil.  That is the default.  You would need a flat start to have the circle perpendicular to the coil curve.  But don't use that technique unless you start the Coil well off of the part, and in any case it will give you results that are harder to understand than simply doing a Coil surface of a line and using the edge of the surface body helix for a Sweep.

Lead Screw.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
JDMather
Posts: 26,651
Registered: ‎04-20-2006
Message 9 of 19 (811 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 07:48 AM in reply to: JDMather

I just realized I left out some steps in that other document - see this one

http://home.pct.edu/~jmather/AU2007/MA105-1L%20Mather.pdf

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Distinguished Contributor
lis_wang
Posts: 433
Registered: ‎11-26-2003
Message 10 of 19 (705 Views)

Re: ball pattern in BALL SCREW assembly

10-18-2012 06:10 PM in reply to: JDMather

Could you please posted the file here? I will installed 2013 in another PC to try it.

 

Thanks

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.