Inventor General Discussion

Inventor General Discussion

Reply
Contributor
knattagh
Posts: 24
Registered: ‎11-18-2012
Message 1 of 11 (461 Views)
Accepted Solution

Automating parameters

461 Views, 10 Replies
11-18-2012 10:45 PM

Hello,

 

I am making a design on inventor 2013 for a collegue who does not know how to use the inventor.

 

I want to make the solid and then set something up that allows the user to change a few of the parameters of the solid in a very user friendly way (i.e. a box that says "cylinder radius" and has an input box so the user can enter a value).

 

Does anyone have any ideas of where I can start?

 

Thanks in advance,

Knattagh

drive your parameters with an excel spreadsheet, then you can add pictures, pretty boxes etc, see attached

 

 

Valued Mentor
stephengibson76
Posts: 1,122
Registered: ‎08-01-2006
Message 2 of 11 (455 Views)

Re: Automating parameters

11-19-2012 01:55 AM in reply to: knattagh

drive your parameters with an excel spreadsheet, then you can add pictures, pretty boxes etc, see attached

 

 

Stephen Gibson



View stephen gibson's profile on LinkedIn


*Pro
sbixler
Posts: 1,968
Registered: ‎09-15-2003
Message 3 of 11 (448 Views)

Re: Automating parameters

11-19-2012 03:58 AM in reply to: knattagh

iLogic will allow you to do this, also, though perhaps without the pictures and pretty boxes!  iLogic can also make sure that the entered paramaters are within proper ranges, if that's important.

Distinguished Contributor
lama
Posts: 121
Registered: ‎09-06-2006
Message 4 of 11 (433 Views)

Re: Automating parameters

11-19-2012 05:21 AM in reply to: sbixler

iLogic, will most certainly allow for pretty pictures.

iLogic Form2.PNG

Larry Marshall
2013 Product Design Suite Ultimate
Windows 7 Sp1
Intel(R) Core (TM) i5-2400 @ 2.00GHz
6.00 GB of RAM
AMD Radeon HD 6570
*Pro
sbixler
Posts: 1,968
Registered: ‎09-15-2003
Message 5 of 11 (424 Views)

Re: Automating parameters

11-19-2012 06:05 AM in reply to: lama

Nice!

Contributor
knattagh
Posts: 24
Registered: ‎11-18-2012
Message 6 of 11 (393 Views)

Re: Automating parameters

11-19-2012 07:40 PM in reply to: lama

Thank you Larry,

 

Could you please tell me how to do this step by step.

 

 

 

Much appreciated

Khash Nattagh

Contributor
knattagh
Posts: 24
Registered: ‎11-18-2012
Message 7 of 11 (392 Views)

Re: Automating parameters

11-19-2012 07:41 PM in reply to: stephengibson76

Thank you Stephen,

 

 

This design also seems very nice and simple, could you please also tell me how to do this step by step.

 

 

 

Thanks again,


Khash nattagh

Valued Mentor
stephengibson76
Posts: 1,122
Registered: ‎08-01-2006
Message 8 of 11 (372 Views)

Re: Automating parameters

11-20-2012 02:45 AM in reply to: knattagh

just use an excel spreadsheet to drive a master part so the only limit is your excel skills, in my case very poor, just inserting a picture

Stephen Gibson



View stephen gibson's profile on LinkedIn


Distinguished Contributor
lama
Posts: 121
Registered: ‎09-06-2006
Message 9 of 11 (345 Views)

Re: Automating parameters

11-20-2012 10:17 AM in reply to: knattagh

I don't have time to give step-by-step instructions for this right now.  I would recommend just going thru the iLogic tutorials and you should have enough information to do something similar to what I've shown above.

Larry Marshall
2013 Product Design Suite Ultimate
Windows 7 Sp1
Intel(R) Core (TM) i5-2400 @ 2.00GHz
6.00 GB of RAM
AMD Radeon HD 6570
Contributor
knattagh
Posts: 24
Registered: ‎11-18-2012
Message 10 of 11 (329 Views)

Re: Automating parameters

11-20-2012 11:15 AM in reply to: stephengibson76

Ok but unfortunately I cannot find any tutorials on how to drive a master part with an excel spreadsheet. Can you refer me somewhere? Sorry I have been using inventor for a couple months.

 

 

Thanks

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.