Inventor General Discussion

Inventor General Discussion

Reply
Employee
johnsonshiue
Posts: 2,335
Registered: ‎04-30-2008
Message 11 of 15 (121 Views)

Re: 'Apply Smooth' on sheet metal parts?

10-01-2012 03:19 PM in reply to: robbieg

Hi! Here is another solution without having to remodel too much. Basically, you just need to create Thicken features to replace the lump having the non-perpendicular detail faces due to the cuts.

After that, you can right-click on the Flat Pattern node in the browser -> Save Copy As -> select DXF -> OK. You might need to adjust the spline conversion tolerance in the DXF OUT process to get the desirable result.

Please let me know if it works for you.

Thanks!

 



Johnson Shiue (johnson.shiue@autodesk.com)
Senior Principal SQA Engineer, Inventor
Mechanical Design
Autodesk, Inc.

*Expert Elite*
JDMather
Posts: 28,221
Registered: ‎04-20-2006
Message 12 of 15 (114 Views)

Re: 'Apply Smooth' on sheet metal parts?

10-01-2012 03:56 PM in reply to: johnsonshiue

After looking at Johnson's solution - I realize I missed one feature in my "solution", but you should be able to figure out and adjust.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Member
robbieg
Posts: 9
Registered: ‎09-21-2011
Message 13 of 15 (88 Views)

Re: 'Apply Smooth' on sheet metal parts?

10-08-2012 08:31 AM in reply to: JDMather

I have now got the part to where you left off regarding the cuts etc. (attached) Can you advise how i go about outputting the splines as chords?

Inventor 2013 SP1
Employee
johnsonshiue
Posts: 2,335
Registered: ‎04-30-2008
Message 14 of 15 (71 Views)

Re: 'Apply Smooth' on sheet metal parts?

10-08-2012 03:41 PM in reply to: johnsonshiue

Hi! Attached is a DXF file output from Inventor Flat Pattern. I used 1mm Linear tolerance (instead of default 0.01mm). Could you take a look and see if it works? If the result is what you are looking for, you can simply do the following to get the same result.

1) Open the Inventor part in Inventor.

2) Activate Flat Pattern to see the Flat Pattern.

3) Right-click on Flat Pattern icon -> Save Copy As -> select DXF or DWG -> Geometry -> change the tolerance from 0.01mm to 1mm ->OK.

 

Please let me know if it works for you.

Thanks!

 



Johnson Shiue (johnson.shiue@autodesk.com)
Senior Principal SQA Engineer, Inventor
Mechanical Design
Autodesk, Inc.

Active Member
robbieg
Posts: 9
Registered: ‎09-21-2011
Message 15 of 15 (58 Views)

Re: 'Apply Smooth' on sheet metal parts?

10-09-2012 02:23 AM in reply to: johnsonshiue

Thankyou that is much closer to what I am looking for, I will have a play around but it looks like I have my solution, cheers

Inventor 2013 SP1
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.