Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
Show only
|
Search instead for
Did you mean:
This page has been translated for your convenience with an automatic translation service. This is not an official translation and may contain errors and inaccurate translations. Autodesk does not warrant, either expressly or implied, the accuracy, reliability or completeness of the information translated by the machine translation service and will not be liable for damages or losses caused by the trust placed in the translation service.Translate
I am current with all Hot-Fixes for IV as well as
all Micro-Soft SP's/Patches. I have checked a couple of machines and on both
machines, the Add-in "Assembly Bonus Tools", "Alpha Sort" runs without
completing its sort. Can others verify this.
Possibly, it was running fine the other day, now it just sits on the re-sort
--
InventorSuite 2010
Dell Precision 690
Dual Quad Core E5320 @ 1.86GHz
4Gb DDR SDRam - 667 Mhz, ECC
SAS 146Gb - 15k rpm
Quadro FX3500 256Mb - Driver: 190.38 Bios: 5.71.22.55.08
Direct 3D
XP Pro Sp3 3Gb/2800
Space Explorer USB, release: 3.7.18 driver 6.7.13 firmware 3.17
AVG 8.5 wrote in message news:6240189@discussion.autodesk.com...
Hi
Here it's work well
IV 2010 pro 32 bit french
HP laptop nw9440 4gb ram
Are you using the defunct ones from the addins Panel, or the new ones that shipped included in 2010 under the Productivity Panel. You should disable the normal Bonus Assembly Tools.
Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.
I have my work station set to the "Classic" and used the add-in within the
header of the "browser" panel. On my laptop I used the "Ribbon" interface
and the Productivity Panel.
--
InventorSuite 2010
Dell Precision 690
Dual Quad Core E5320 @ 1.86GHz
4Gb DDR SDRam - 667 Mhz, ECC
SAS 146Gb - 15k rpm
Quadro FX3500 256Mb - Driver: 190.38 Bios: 5.71.22.55.08
Direct 3D
XP Pro Sp3 3Gb/2800
Space Explorer USB, release: 3.7.18 driver 6.7.13 firmware 3.17
AVG 8.5 wrote in message news:6240215@discussion.autodesk.com...
Are you using the defunct ones from the addins Panel, or the new ones that
shipped included in 2010 under the Productivity Panel. You should disable
the normal Bonus Assembly Tools.
It's works on a small assembly (less than 20 parts) but try it on a larger
IAM file, something in excess of 500 parts. This shouldn't take over 5
minutes on this machine to sort a 501/132 assembly.
--
InventorSuite 2010
Dell Precision 690
Dual Quad Core E5320 @ 1.86GHz
4Gb DDR SDRam - 667 Mhz, ECC
SAS 146Gb - 15k rpm
Quadro FX3500 256Mb - Driver: 190.38 Bios: 5.71.22.55.08
Direct 3D
XP Pro Sp3 3Gb/2800
Space Explorer USB, release: 3.7.18 driver 6.7.13 firmware 3.17
AVG 8.5 wrote in message news:6240215@discussion.autodesk.com...
Are you using the defunct ones from the addins Panel, or the new ones that
shipped included in 2010 under the Productivity Panel. You should disable
the normal Bonus Assembly Tools.
![Autodesk Design & Make Report](https://forums.autodesk.com/t5/image/serverpage/image-id/1350519iCB55845EBFC43016/image-size/large?v=v2&px=999" "Autodesk Design & Make Report")