InfraWorks General Discussion

InfraWorks General Discussion

Reply
Distinguished Contributor
jmaeding
Posts: 1,054
Registered: ‎12-27-2006
Message 1 of 9 (516 Views)

crash on exit

516 Views, 8 Replies
06-06-2012 05:42 PM

any fixes in the works for the crash 2013 gives when closing?

Does everyone get them for 2013?

internal protected virtual unsafe Human()
http://onesmallstepforcad.com/

Distinguished Contributor
jmaeding
Posts: 1,054
Registered: ‎12-27-2006
Message 2 of 9 (502 Views)

Re: crash on exit

06-13-2012 09:32 AM in reply to: jmaeding

ok, I did a subscription support request on this, anyone getting the (2013) crashes, please let me know.

 

internal protected virtual unsafe Human()
http://onesmallstepforcad.com/

Employee
nzeeben
Posts: 92
Registered: ‎09-22-2008
Message 3 of 9 (500 Views)

Re: crash on exit

06-13-2012 10:39 AM in reply to: jmaeding

James,

 

We are researching this.  It is not consistent across machines/platforms etc.  Please make sure you submit the error report if you get it.  

 

Thanks

Nick

Distinguished Contributor
jmaeding
Posts: 1,054
Registered: ‎12-27-2006
Message 4 of 9 (498 Views)

Re: crash on exit

06-13-2012 11:30 AM in reply to: nzeeben

thanks for the reply.

Let me know if there are any environment issues you would like to know, like what is installed.

internal protected virtual unsafe Human()
http://onesmallstepforcad.com/

*Expert Elite*
DarrenP
Posts: 7,686
Registered: ‎09-13-2007
Message 5 of 9 (495 Views)

Re: crash on exit

06-14-2012 06:21 PM in reply to: jmaeding
i had this problem to it only happened on the very 1st launch after installation
Distinguished Contributor
jmaeding
Posts: 1,054
Registered: ‎12-27-2006
Message 6 of 9 (466 Views)

Re: crash on exit

08-01-2012 09:34 AM in reply to: DarrenP

autodesk, any updates on this?

internal protected virtual unsafe Human()
http://onesmallstepforcad.com/

Employee
konstantin.baumann
Posts: 88
Registered: ‎01-04-2011
Message 7 of 9 (459 Views)

Re: crash on exit

08-02-2012 01:33 AM in reply to: jmaeding

How often does that happen on your machine? From time to time? Everytime you close AIM? Only the first time you start AIM after a fresh reboot of your system? 32 bit or 64 bit version? ...?

Active Contributor
Kevin.Spear
Posts: 40
Registered: ‎05-15-2012
Message 8 of 9 (426 Views)

Re: crash on exit

08-17-2012 10:52 AM in reply to: jmaeding

Crash on launch - actually it becomes unresponsive and have to kill the process....

Thanks
Kevin


Kevin Spear, PE
Synergis Engineering Design Solutions
Valued Contributor
KevinSpear_PE
Posts: 70
Registered: ‎04-09-2009
Message 9 of 9 (408 Views)

Re: crash on exit

08-20-2012 10:40 AM in reply to: jmaeding

Turns out i needed to repair both .NET Framework components (Extended & Client Profile), then everything worked.

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.