DWG TrueView

Reply
Active Member
starkjerry
Posts: 6
Registered: ‎04-24-2013
Message 1 of 11 (2,066 Views)

print pieces of a dwg file

2066 Views, 10 Replies
04-24-2013 03:30 PM

I have no experience with autocad at all.

I have a .dwg file that contains a wiring schematic for my RV, which the mfg'r was nice enough to send me . My goal is to break the .dwg file up into 9 pieces that I could print and keepi n the RV.

I downloaded Autodesk autocad design suite free trial because it can handle Trueview files. I had loaded the .dwg file with autodesk, but it indicated something about not the Heidi driver cannot load and would use a default software driver. This was the dwgviewr.exe application in autodesk directory.  Using this I am able to open the file and view it. I can zoom in and out. I tried to print it and it shrunk the view to an unreadable blob. The schematic has horizontal section markers A to H and vertical section markers 1 to 10.  The horizonal numbers on the edges of the view go from -146 to 392 while the vertical numbers go from 1203 to 130 (leaving out the decimals). 

The output tab has Plot, Btach Plot, and Preview items which indicates to me that it thinks it is in a plot format?

I looked  up how to set a plot area and tried to set a window to of 264 x 775 in an attempt to create 9 sections which I could print on a printer. This was the one I hoped would be of the upper left corner. I sent it to a file with the extension of .plt(trueview's choice), with hopes of viewing it to see how it would look. I could not find anyway to view it. Autodesk could not find a file that did not have an extension other than .dwg.

Does anyone have any experience in trying to do this?

Any help would be appreciated. I do not know of another way to do this.

 

*Expert Elite*
Charles_Shade
Posts: 8,204
Registered: ‎04-10-2005
Message 2 of 11 (2,056 Views)

Re: print pieces of a dwg file

04-24-2013 06:18 PM in reply to: starkjerry

Post your DWG file.

8-1/2 x 11 okay for the PDF's?

Regards, Charles Shade            Win8 FAQ
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS

 
Please mark Accept as Solution if your question is answered. Kudos gladly accepted.
Active Member
starkjerry
Posts: 6
Registered: ‎04-24-2013
Message 3 of 11 (2,049 Views)

Re: print pieces of a dwg file

04-25-2013 10:21 AM in reply to: Charles_Shade

I have attached the file 38011139.dwg.

I tried insert but it saidit was an error. Hope this incudes it.

 

*Expert Elite*
Charles_Shade
Posts: 8,204
Registered: ‎04-10-2005
Message 4 of 11 (2,044 Views)

Re: print pieces of a dwg file

04-25-2013 12:24 PM in reply to: starkjerry

See if these will do.

Might be too small to read

Regards, Charles Shade            Win8 FAQ
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS

 
Please mark Accept as Solution if your question is answered. Kudos gladly accepted.
Active Member
starkjerry
Posts: 6
Registered: ‎04-24-2013
Message 5 of 11 (2,040 Views)

Re: print pieces of a dwg file

04-25-2013 03:25 PM in reply to: Charles_Shade

Thanks,

Yes they are a little hard to read, a little bigger would be better. Its not that bad but my eyes aren't what they used to be.

Would it be possible to also make them slightly larger so they over lap each other. This would make it a lot easier to trace a signal line from one page to another page. It doesn't equire much overlap, maybe enough to tape them together.

How ever you did this I hope it didn't take too much of your time.

*Expert Elite*
Charles_Shade
Posts: 8,204
Registered: ‎04-10-2005
Message 6 of 11 (2,037 Views)

Re: print pieces of a dwg file

04-26-2013 04:41 AM in reply to: starkjerry

No its pretty quick and I will make larger for you in the next couple days.

It may be 20-30 sheets when finished though. Might run out of alphabet.:smileywink:

I did wonder if what I did would leave the lines not meeting one another.

 

This was done with using AutoCAD LT and the built in PDF driver. You could download a Trial of the Program and do the same just by creating a grid of the paper (8-1/2 x 11) over the schematic and using Print,(Plot Areae) Window to pick each corner of the grid.

Where the overlap comes is that each grid needs to be overlapping the other by some amount (1/2"?) to get a "full bleed" as they say.

Regards, Charles Shade            Win8 FAQ
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS

 
Please mark Accept as Solution if your question is answered. Kudos gladly accepted.
Active Member
starkjerry
Posts: 6
Registered: ‎04-24-2013
Message 7 of 11 (2,031 Views)

Re: print pieces of a dwg file

04-26-2013 09:19 AM in reply to: Charles_Shade

The print need to only slightly larger. 

Also when I look at the .dwg file some of the detail is shown in yellow. Can this be made a different color as it shows up very faint when printed on a non-color printer.

Thanks for the description of you did this. it sounds easier  to do.  Again I appreciate it.

 

Active Member
starkjerry
Posts: 6
Registered: ‎04-24-2013
Message 8 of 11 (1,994 Views)

Re: print pieces of a dwg file

05-08-2013 09:47 AM in reply to: starkjerry

Are you still planning to remake the sheets for me.  I figured you must be busy or on vacation so I waited a while to ask. If not maybe I can work with the ones you made available before.

*Expert Elite*
Charles_Shade
Posts: 8,204
Registered: ‎04-10-2005
Message 9 of 11 (1,991 Views)

Re: print pieces of a dwg file

05-08-2013 11:48 AM in reply to: starkjerry
Sorry got busy and forgot about this. Would you please click on my name and PM me with a link to this thread so I will get back to it
Regards, Charles Shade            Win8 FAQ
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS

 
Please mark Accept as Solution if your question is answered. Kudos gladly accepted.
Active Member
starkjerry
Posts: 6
Registered: ‎04-24-2013
Message 10 of 11 (1,973 Views)

Re: print pieces of a dwg file

05-13-2013 05:58 PM in reply to: starkjerry

I am not sure if you got what you needed. I gues you my previous message here. so I sent a link to this topic and hoped you would get it. evidently you are still busy or you never got what you asked for. Maybe I do not know what PM means? Not sure what to do next?

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are You Going To Be @ AU 2014? Feel free to drop by our AU topic post and share your plans, plug a class that you're teaching, or simply check out who else from the community might be in attendance. Ohh and don't forgot to stop by the Autodesk Help | Learn | Collaborate booths in the Exhibit Hall and meet our community team if you get a chance!