Design Review

Design Review

Reply
Distinguished Contributor
KobusE
Posts: 197
Registered: ‎10-01-2006
Message 1 of 4 (260 Views)

Electronic review using ADR and Vault Collaboration

260 Views, 3 Replies
03-15-2012 04:43 AM

Hi,

Our company is implementing an electronic review system for commenting and marking up on drawings.  For this we have procured a 46" touch screen system with built in pc, linked it to our network, loaded Vault Collaboration 2012, IV 2012, ADR 2012.  It has its own email address and is located in our project drawing area.  I have been able to set it up to open drawings from Vault, mark it up in ADR, save it and check back into Vault.  We also have an office in India contributing to our project that also uses Vault Collaboration 2012 - we are still working on the interaction between their Vault and ours.

 

Now the questions:

1. I'd like any comments on lessons learnt from anyone that has implemented something like this before.

2. Signing off (wet signature equivalent) of drawings on ADR?  How do I accomplish that?

3. How does digital signatures feature in a setup like this?

 

Frankly any suggestions or ideas are welcome.

 

Regards

 

Kobus

 

Active Contributor
vgottipa
Posts: 31
Registered: ‎02-10-2011
Message 2 of 4 (257 Views)

Re: Electronic review using ADR and Vault Collaboration

03-15-2012 07:09 AM in reply to: KobusE

Hello,

 

This looks like an interesting project. Sorry for going off-topic, but I found Autodesk Buzzsaw to be good at drawings colloboration. I am sure you may have heard or used it before. It includes a lot of similar and additional functionality. One of the cool things I like about it is the Compare feature to automatically highlight the revisions. You could acheive this functionality with plain design review as well, but that would involve having both the old and new versions of the dwf on your hard drive. Good luck anyway.

 

Thanks

Distinguished Contributor
KobusE
Posts: 197
Registered: ‎10-01-2006
Message 3 of 4 (253 Views)

Re: Electronic review using ADR and Vault Collaboration

03-15-2012 11:25 AM in reply to: vgottipa

Buzzsaw actually forms part of our communication channel with our Indian office.  We currently use it to exchange Vault information by synchronising the entire Vault (Inventor and Autocad files) with them.  They then download and upload files as needed.

 

However, we'd like Vault to be our main system and using Autodesk Design Review as our drawing squad check system  Actually this post can be looked at from three different groups - ADR, Vault Collaboration as well as Buzzsaw.

 

You're correct, this is actually an interesting project, even though i am doing this concurrently with being section lead for a "real" project as well.

 

Thanks for your comments.

Member
iqbal.lotey
Posts: 10
Registered: ‎05-23-2013
Message 4 of 4 (153 Views)

Re: Electronic review using ADR and Vault Collaboration

05-27-2014 01:19 PM in reply to: KobusE

Hi Kobus,

 

If you're still watching this thread, how did your markup process work out?  We are also trying to figure out how to make DWF markups work in Vault, and am intrigued as to how you got it "to open drawings from Vault, mark it up in ADR, save it and check back into Vault"

 

Thanks,

  Iqbal.

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.