AutoCAD Structural Detailing General DIscussion

AutoCAD Structural Detailing General DIscussion

Reply
Active Member
jpassociates
Posts: 6
Registered: ‎07-30-2012
Message 1 of 10 (1,142 Views)
Accepted Solution

Macros

1142 Views, 9 Replies
08-25-2012 06:21 AM

I used the base plate macro and made a elongated cap plate with holes. It seems to work ok on one column line, but It needs it to mirrored on the opposite column line. It's not working, what am I doing wrong. HELP.

Look at movie here.

---------------------------------------------
If this post answer your question please click "Accept as Solution". It will help everyone to find answer more quickly!

Valued Contributor
lucis29
Posts: 69
Registered: ‎03-04-2010
Message 2 of 10 (1,113 Views)

Re: Macros

08-29-2012 03:12 AM in reply to: jpassociates

Please add some pictures.

 

Mirror command only works in XY plane!!!

Active Member
jpassociates
Posts: 6
Registered: ‎07-30-2012
Message 3 of 10 (1,045 Views)

Macros

08-29-2012 06:13 PM in reply to: jpassociates

I am using the the base plate macro. I am trying to have a 2-hole on 1-side 6" apart and at 90 deg. 2-more holes 6" apart 18"x18"x1 1/4" PL. I got it to work one side but i couldn't on the 90 deg. side. Thanks 

Valued Mentor
Rich.O.3d
Posts: 526
Registered: ‎08-19-2008
Message 4 of 10 (1,097 Views)

Re: Macros

08-30-2012 04:27 PM in reply to: jpassociates

from what I have seen, ASD does not play well with the mirror command

CAD Management 101:
You can do it your own way,
If its done just how I say!
[Metallica:And Justice For All:1988]
Active Member
jpassociates
Posts: 6
Registered: ‎07-30-2012
Message 5 of 10 (1,083 Views)

Re: Macros

08-31-2012 05:24 AM in reply to: jpassociates

If I can't use this base plate macro for this particular plate. Could I use the plate macro and add holes where I need them? If so, How would this work.  

Product Support
Jakub.Brozonowicz
Posts: 317
Registered: ‎12-13-2010
Message 6 of 10 (1,075 Views)

Re: Macros

08-31-2012 07:20 AM in reply to: jpassociates

Do you have any chance to show it please?



Jakub Brożonowicz
Active Member
jpassociates
Posts: 6
Registered: ‎07-30-2012
Message 7 of 10 (1,071 Views)

Re: Macros

08-31-2012 09:41 AM in reply to: jpassociates
Product Support
Jakub.Brozonowicz
Posts: 317
Registered: ‎12-13-2010
Message 8 of 10 (1,032 Views)

Re: Macros

09-03-2012 03:14 AM in reply to: jpassociates

Look at movie here.

---------------------------------------------
If this post answer your question please click "Accept as Solution". It will help everyone to find answer more quickly!



Jakub Brożonowicz
Active Member
jpassociates
Posts: 6
Registered: ‎07-30-2012
Message 9 of 10 (1,016 Views)

Re: Macros

09-04-2012 05:19 AM in reply to: jpassociates

Thanks for the solution.

Active Member
jpassociates
Posts: 6
Registered: ‎07-30-2012
Message 10 of 10 (928 Views)

Re: Macros

09-12-2012 04:05 AM in reply to: Jakub.Brozonowicz
Holes needed at clouded area. With all the hole variations for that base plate macro, I can't get it to show those clouded holes. Help please.
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions to get help installing your software.

New AutoCAD Structural Detailing Category!

The AutoCAD Structural Detailing forum has moved into it's very own category page, and can no longer be found within the Additional Product Forums.

Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.