AutoCAD Structural Detailing General DIscussion

AutoCAD Structural Detailing General DIscussion

Reply
Active Member
Rick
Posts: 8
Registered: ‎06-28-2012
Message 1 of 6 (512 Views)

ASD Dimensioning and call outs (style)

512 Views, 5 Replies
10-12-2012 03:34 PM

Is it possible to change the ASD generated call out on prints form:

2 Ø ½” to 2 - ½” Ø or just get the hole symbol Ø at the end of the call out

Product Support
Jakub.Brozonowicz
Posts: 317
Registered: ‎12-13-2010
Message 2 of 6 (471 Views)

Re: ASD Dimensioning and call outs (style)

10-15-2012 02:18 AM in reply to: Rick

Would you like to check attached movie?

Is this what solves your problem after change in default style?

 

---------------------------------------------
If this post answer your question please click "Accept as Solution". It will help everyone to find answer more quickly!



Jakub Brożonowicz
Active Member
Rick
Posts: 8
Registered: ‎06-28-2012
Message 3 of 6 (457 Views)

Re: ASD Dimensioning and call outs (style)

10-15-2012 09:14 AM in reply to: Jakub.Brozonowicz
I could not open the file Using windows 7 and windows explorer plus I down loaded the adobe flash. Could not get it to run. Thanks you for the reply would love to find the answer. [- Description: SS_logo_1x1] Rick Thompson Superior Steel and Ironworkers LLC 21229 84th Avenue South Kent, WA 98027 425-677-8100 Office | 866-588-4766 Fax | 206-450-0794 Cell rickthompson@superiorsteel.comThis message contains confidential information intended only for use by the intended recipient(s). If you are not an intended recipient any distribution, duplication or use of this message or any attachments is not permitted. If you received this message in error please immediately advise the sender by reply e-mail and delete the original message. Thank you
Product Support
Jakub.Brozonowicz
Posts: 317
Registered: ‎12-13-2010
Message 4 of 6 (438 Views)

Re: ASD Dimensioning and call outs (style)

10-16-2012 12:29 AM in reply to: Rick

Please find the video here .



Jakub Brożonowicz
Active Member
Rick
Posts: 8
Registered: ‎06-28-2012
Message 5 of 6 (426 Views)

Re: ASD Dimensioning and call outs (style)

10-16-2012 11:22 AM in reply to: Jakub.Brozonowicz
The video on modifying the style is of help. And thank you but what I would like is to change the style so it is a standard. so they will always look that way. Change it in ASD [- Description: SS_logo_1x1] Rick Thompson
Product Support
Jakub.Brozonowicz
Posts: 317
Registered: ‎12-13-2010
Message 6 of 6 (401 Views)

Re: ASD Dimensioning and call outs (style)

10-18-2012 07:39 AM in reply to: Rick

Request for change was sent.



Jakub Brożonowicz
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions to get help installing your software.

New AutoCAD Structural Detailing Category!

The AutoCAD Structural Detailing forum has moved into it's very own category page, and can no longer be found within the Additional Product Forums.

Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.