AutoCAD MEP General Discussion

AutoCAD MEP General Discussion

Reply
Active Contributor
TravelTheWorld
Posts: 30
Registered: ‎12-01-2009
Message 1 of 11 (7,493 Views)

CadDuct Object Enabler Problem

7493 Views, 10 Replies
02-10-2010 05:13 AM
Hi,

I have installed MEP 2010 on my computer, and I haven't been able to view drawings drawn with CadDuct. I have installed Autocad Object Enabler and CADmep+ & CADduct Object Enabler on my computer, but I still won't be able to view them. When I opened a CadDuct drawing with my MEP 2010, all I could see was some blocks and texts, not duct work.

Has any of you encountered this problem? If so, what was it you did to resolve this problem?

Thank you,
New Member
charlie.quebe
Posts: 2
Registered: ‎06-30-2009
Message 2 of 11 (7,492 Views)

Re: CadDuct Object Enabler Problem

02-11-2010 10:22 AM in reply to: TravelTheWorld
I had the same problem so I exported the CadDuct drawing to AutoCAD 2007 format and it worked.
*Mike
Message 3 of 11 (7,493 Views)

Re: CadDuct Object Enabler Problem

02-11-2010 11:53 AM in reply to: TravelTheWorld
I had the same problem in MEP 2009 and when I loaded the mapcadduct.dbx file
manuallly using application load, it worked.




"jasonpark0911" wrote in message news:6333761@discussion.autodesk.com...
Hi,

I have installed MEP 2010 on my computer, and I haven't been able to view
drawings drawn with CadDuct. I have installed Autocad Object Enabler and
CADmep+ & CADduct Object Enabler on my computer, but I still won't be able
to view them. When I opened a CadDuct drawing with my MEP 2010, all I could
see was some blocks and texts, not duct work.

Has any of you encountered this problem? If so, what was it you did to
resolve this problem?

Thank you,
Member
aaronkrawchuk1613
Posts: 3
Registered: ‎12-15-2011
Message 4 of 11 (6,075 Views)

Re: CadDuct Object Enabler Problem

05-23-2012 09:38 AM in reply to: TravelTheWorld

Anyone have a 2013 version for this enabler yet.. I am receiving drawings from subs and cannot get their items to show up... AutoCAD says it cannot load the .dbx file...  I am not sure if it is old or not compadible to AutoDesk 2013 versions

Board Manager
Nicholas.Hyland
Posts: 25
Registered: ‎11-01-2011
Message 5 of 11 (5,514 Views)

Re: CadDuct Object Enabler Problem

08-13-2012 06:57 AM in reply to: aaronkrawchuk1613

Hi,

 

Here are the details for the CADmep object enablers:

 

Fabrication CADmep 2013 object enabler (for 2013 products only)

http://knowledge.autodesk.com/support/autocad/downloads/caas/downloads/content/autodesk-fabrication-...

CADmep legacy enabler for AutoCAD 2009-2012 (as *Mike mentions, this version requires manual registration with AutoCAD)

http://knowledge.autodesk.com/support/fabrication-products/downloads/caas/downloads/content/legacy-v...

 

Hope this helps.

Nick



Nicholas Hyland
New Member
rmc1111
Posts: 2
Registered: ‎09-12-2013
Message 6 of 11 (2,670 Views)

Re: CadDuct Object Enabler Problem 2014

09-12-2013 04:32 AM in reply to: TravelTheWorld

2014 NAVISWORK

UPGRADED FROM AUTOCAD 2013 TO 2014 ALSO THE SAME WITH NAVISWORK AND I ALSO INSTALLED AUTODESK FABRICATION CADMEP 2014 OBJECT ENABLER I  HAVE SUB-CONTRACTOR WHO USES CADDUCT SOFTWARE AND I AM NOT ABLE TO SEE THE DUCT IN 2014 NAVIS IT WAS FINE IN 2013 IS THERE ANY PATCHES OUT THERE TO CORRECT THIS PROMBLEM THANKS

Active Contributor
rsloyer
Posts: 45
Registered: ‎04-09-2009
Message 7 of 11 (2,320 Views)

Re: CadDuct Object Enabler Problem 2014

10-11-2013 12:41 PM in reply to: rmc1111

ks like I'm having a simlilar issue but with AutoCAD MEP 2014.  Are there enablers for CADduct to MEP 2014?

Board Manager
Nicholas.Hyland
Posts: 25
Registered: ‎11-01-2011
Message 8 of 11 (2,224 Views)

Re: CadDuct Object Enabler Problem 2014

10-17-2013 09:19 AM in reply to: rsloyer
New Member
jamesbon
Posts: 1
Registered: ‎03-27-2014
Message 9 of 11 (1,248 Views)

Re: CadDuct Object Enabler Problem 2014

03-27-2014 10:29 AM in reply to: Nicholas.Hyland
Is there a way to get the Autodesk Fabrication CADmep Object Enabler to function in Design Review or TrueView 2015? And if so, how? Thank you in advance.
Board Manager
Nicholas.Hyland
Posts: 25
Registered: ‎11-01-2011
Message 10 of 11 (1,228 Views)

Re: CadDuct Object Enabler Problem 2014

03-28-2014 03:51 AM in reply to: jamesbon

The Fabrication CADmep 2015 object enabler will need to be installed, I'll post a link once released.



Nicholas Hyland
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions to get help installing your software.

New AutoCAD MEP Category!

The AutoCAD MEP forum has moved into it's very own category page, and can no longer be found within the Additional Product Forums.