AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
Contributor
rvandever21
Posts: 16
Registered: ‎09-19-2012
Message 1 of 17 (5,406 Views)

Rotate drawing in viewport

5406 Views, 16 Replies
12-05-2012 09:54 AM

How do I rotate the drawing in viewport?

 

I want to have my profile and alignment to be in the same orientation on paper space. I have VPROTATEASSOC set to 1. I am not sure if I am using UCS and MVSETUP correctly.  All information will work.

 

Thank you,

Rochelle Vandever

*Expert Elite*
tcorey
Posts: 2,646
Registered: ‎12-18-2002
Message 2 of 17 (5,405 Views)

Re: Rotate drawing in viewport

12-05-2012 09:56 AM in reply to: rvandever21

Use two viewports. In the profile viewport, no rotation at all. In the alignment viewport, use Dview with Twist option.

 

 

Tim Corey, Owner
Delta Engineering Systems
Redding, CA
Autodesk Authorized Value-Added Reseller
Contributor
rvandever21
Posts: 16
Registered: ‎09-19-2012
Message 3 of 17 (5,400 Views)

Re: Rotate drawing in viewport

12-05-2012 10:11 AM in reply to: tcorey

I tried to use the DVIEW on my viewport. It says I could only use dview in model space.

*Expert Elite*
tcorey
Posts: 2,646
Registered: ‎12-18-2002
Message 4 of 17 (5,395 Views)

Re: Rotate drawing in viewport

12-05-2012 10:16 AM in reply to: rvandever21

If you double click inside the alignment's viewport, you will be in modelspace (not to be confused with the Model tab.) Use Dview from there.

Tim Corey, Owner
Delta Engineering Systems
Redding, CA
Autodesk Authorized Value-Added Reseller
Contributor
rvandever21
Posts: 16
Registered: ‎09-19-2012
Message 5 of 17 (5,388 Views)

Re: Rotate drawing in viewport

12-05-2012 10:44 AM in reply to: tcorey

I was able to rotate the drawing but I can scale or move the drawing to line up the profile. Is there a way to keep the rotate but turn off dview?

*Expert Elite*
troma
Posts: 2,524
Registered: ‎05-21-2008
Message 6 of 17 (5,378 Views)

Re: Rotate drawing in viewport

12-05-2012 11:21 AM in reply to: rvandever21

When you get the rotation right, set the scale of the viewport.  Then lock the viewport to prevent accidentally changing the scale later.  Both the scale and the lock can be found at the bottom right of your main screen, or in the properties pallette.

Once you've done that you can move the viewport around in paper space, and stretch it bigger or smaller as necessary.


Credit where credit is due! Give kudos or accept as solution whenever you can.

*Expert Elite*
troma
Posts: 2,524
Registered: ‎05-21-2008
Message 7 of 17 (5,376 Views)

Re: Rotate drawing in viewport

12-05-2012 11:22 AM in reply to: rvandever21

I just re-read your question; do you need to hit enter one more time to exit out of the dview command?


Credit where credit is due! Give kudos or accept as solution whenever you can.

Contributor
rvandever21
Posts: 16
Registered: ‎09-19-2012
Message 8 of 17 (5,373 Views)

Re: Rotate drawing in viewport

12-05-2012 11:30 AM in reply to: troma

I still have the dview command on but when I escape to move the drawing.  The alignment will change back to the original drawing.

*Expert Elite*
troma
Posts: 2,524
Registered: ‎05-21-2008
Message 9 of 17 (5,361 Views)

Re: Rotate drawing in viewport

12-05-2012 11:52 AM in reply to: rvandever21

Don't hit Escape

Hit Enter instead.


Credit where credit is due! Give kudos or accept as solution whenever you can.

*Expert Elite*
LeafRiders
Posts: 331
Registered: ‎09-28-2010
Message 10 of 17 (5,323 Views)

Re: Rotate drawing in viewport

12-06-2012 11:55 AM in reply to: troma

This is a pretty painful solution...

 

Use UCS (enter) 3 (enter) click two points (left to right), this will be come your new West to East (left to right).

 

Final step.... Type PLAN (enter) (enter)... Proceed to set the scale of your viewport and then lock it as suggested. Good Luck!

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.