AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
Valued Mentor
ralstogj
Posts: 616
Registered: ‎10-01-2006
Message 1 of 9 (805 Views)
Accepted Solution

Quickest way to delete curve from featureline?

805 Views, 8 Replies
01-31-2012 04:57 PM

Suggestions. Anyone

 

Regards

Justin Ralston
http://c3dxtreme.blogspot.com/

The delete option is not fast enough?:smileywink:

 

fl curve delete.PNG

*Expert Elite*
Joe-Bouza
Posts: 5,189
Registered: ‎12-15-2008
Message 2 of 9 (798 Views)

Re: Quickest way to delete curve from featureline?

01-31-2012 06:18 PM in reply to: ralstogj

The delete option is not fast enough?:smileywink:

 

fl curve delete.PNG

Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People) Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win7 OS
Valued Mentor
ralstogj
Posts: 616
Registered: ‎10-01-2006
Message 3 of 9 (796 Views)

Re: Quickest way to delete curve from featureline?

01-31-2012 06:21 PM in reply to: Joe-Bouza

Operate this software with my eye shut. Thanks

 

 

Regards

Justin Ralston
http://c3dxtreme.blogspot.com/
*Expert Elite*
AllenJessup
Posts: 6,183
Registered: ‎05-21-2003
Message 4 of 9 (769 Views)

Re: Quickest way to delete curve from featureline?

02-01-2012 05:53 AM in reply to: Joe-Bouza

Or the condensed versionEditFeatureCurve. It's funny that Help [in 2011] says the command supports 2D & 3D polylines and Lines. Since none of those support curves.

 

Allen

*Expert Elite*
Joe-Bouza
Posts: 5,189
Registered: ‎12-15-2008
Message 5 of 9 (743 Views)

Re: Quickest way to delete curve from featureline?

02-02-2012 11:57 AM in reply to: ralstogj

Me too. Reading this board helps open them.

Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People) Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win7 OS
*Expert Elite*
AllenJessup
Posts: 6,183
Registered: ‎05-21-2003
Message 6 of 9 (708 Views)

Re: Quickest way to delete curve from featureline?

02-12-2012 12:12 PM in reply to: Joe-Bouza

OK. Is there a way to Straighten the curve without deleting it?

 

Allen

*Expert Elite*
Joe-Bouza
Posts: 5,189
Registered: ‎12-15-2008
Message 7 of 9 (702 Views)

Re: Quickest way to delete curve from featureline?

02-12-2012 01:17 PM in reply to: ralstogj

Tying to be helpful by testing a solution - I just crashe c3d and lost an hours worth of work :smileysad:

 

In any event, I think you can only straightne a FL that has been previously Smoothed, otherwise it delete curves.

Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People) Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win7 OS
*Expert Elite*
AllenJessup
Posts: 6,183
Registered: ‎05-21-2003
Message 8 of 9 (700 Views)

Re: Quickest way to delete curve from featureline?

02-12-2012 01:40 PM in reply to: Joe-Bouza

Very sorry about that Joe. I see you're burning the weekend oil too. I tried tracking down a couple of blogs that hinted you could use Pedit-Straighten. But you can't use Pedit on Featurelines.

 

I suppose you could explode the FL, Pedit it and turn it back to an FL. I ended up deleting the curve, adding a straight featureline and joining that back to the remaining segments.

 

Again. My regrets. No chance of recovering an Autosave file?

 

Allen

*Expert Elite*
Joe-Bouza
Posts: 5,189
Registered: ‎12-15-2008
Message 9 of 9 (692 Views)

Re: Quickest way to delete curve from featureline?

02-12-2012 03:05 PM in reply to: ralstogj

No worries, yes I have many backup.

Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People) Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win7 OS
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.