AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
Active Contributor
47 Posts
0 Kudos
Registered: ‎01-09-2012
Post 1 of 7
Accepted Solution

OVERLAYWIDENWITHSUPER1 zero cross slope glitch

261 Views, 6 Replies
11-02-2012 02:58 PM

with the default cross slope 2% in place and no profile targets, section views with subject sub assembly come up at 0%

 

there's some polyline width targets but no verticals...

 

any thoughts?

 

thx!

The superelevation parameters won't calculate and the software won't allow you to add anything until you have a design speed set for the alignment.  Open the Alignment Properties dialog, switch to the Design Criteria tab and use the button to add one.

Clipboard01.png

I tried some experimenting with a single tangent alignment like yours and ran into the same problem - without any curves you cannot enter any superelevation values.  I ended up adding a very small three point curve to the end of the alignment then used masking to hide it.  Once that was done I could add the superelevation.

*Expert Elite*
2,293 Posts
418 Kudos
Registered: ‎11-08-2005
Post 2 of 7

Re: OVERLAYWIDENWITHSUPER1 zero cross slope glitch

11-03-2012 10:53 PM in reply to: torpedo99

Check the superelevation parameters for the alignment.

Active Contributor
47 Posts
0 Kudos
Registered: ‎01-09-2012
Post 3 of 7

Re: OVERLAYWIDENWITHSUPER1 zero cross slope glitch

11-04-2012 09:01 AM in reply to: sboon

the alignment has no super parameters, therefore it seems the defaults in the subassemblies should dictate

 

other thoughts?

 

thx,

*Expert Elite*
2,293 Posts
418 Kudos
Registered: ‎11-08-2005
Post 4 of 7

Re: OVERLAYWIDENWITHSUPER1 zero cross slope glitch

11-04-2012 09:38 AM in reply to: torpedo99

I just checked the help and the parameters for the sub.  I don't see a default slope parameter, and the help indicates that the lane slope always comes from the superelevation.  Perhaps we're talking about different subassemblies or different versions?

 

Clipboard99.png

 

Active Contributor
47 Posts
0 Kudos
Registered: ‎01-09-2012
Post 5 of 7

Re: OVERLAYWIDENWITHSUPER1 zero cross slope glitch

11-04-2012 10:09 AM in reply to: sboon

I'm using 2012

 

In help under "layout mode operation" it sure seems to imply -2%, also in your graphic it shows a -2% slope value...

 

But I'm guessing you're on the right track.  However I've got a long tangent road and the super wizard simply returns "no curves on alignment" and the tabular editor won't let me add anything.  So I can't simply add 2% normal crown for the length of the roadway, hoping the assembly would kick in.

 

Any last thoughts?

 

again much obliged,

*Expert Elite*
2,293 Posts
418 Kudos
Registered: ‎11-08-2005
Post 6 of 7

Re: OVERLAYWIDENWITHSUPER1 zero cross slope glitch

11-04-2012 05:40 PM in reply to: torpedo99

The superelevation parameters won't calculate and the software won't allow you to add anything until you have a design speed set for the alignment.  Open the Alignment Properties dialog, switch to the Design Criteria tab and use the button to add one.

Clipboard01.png

I tried some experimenting with a single tangent alignment like yours and ran into the same problem - without any curves you cannot enter any superelevation values.  I ended up adding a very small three point curve to the end of the alignment then used masking to hide it.  Once that was done I could add the superelevation.

Active Contributor
47 Posts
0 Kudos
Registered: ‎01-09-2012
Post 7 of 7

Re: OVERLAYWIDENWITHSUPER1 zero cross slope glitch

11-05-2012 06:58 AM in reply to: sboon

you da man!

 

Thank you!

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are you interested in helping shape the future of the Autodesk Community? To participate in this brief usability study, please click here. Your time and input is greatly appreciated!