Community
Civil 3D Forum
Welcome to Autodesk’s Civil 3D Forums. Share your knowledge, ask questions, and explore popular AutoCAD Civil 3D topics.
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

OverlayWidenWithSuper

5 REPLIES 5
SOLVED
Reply
Message 1 of 6
Joe-Bouza
363 Views, 5 Replies

OverlayWidenWithSuper

I trying theOWWS for the first time and something are not going so smoothly. I though I understood the parameters but I have something wrong:

 

1. The control point I am using is my baseline alignent for crown

2. The insert point I figured I tie to a saw cut line alignment

3. The widening width to the eop alignment

 

All that looks good, But it does not appear to be reading the super elevation from the alignment (its been calculated) the section viewer is all default 2% through the curves. What did I do wrong?

 

Also, am I correct in thinking I need 2  assembly for left side and right?

Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People)

HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win10 OS
5 REPLIES 5
Message 2 of 6
sboon
in reply to: Joe-Bouza

I just tried it here with a tutorial drawing, and everything works fine for me.  Perhaps you calcuated the Inside Lane supers by mistake?

 

Steve
Please use the Accept as Solution or Kudo buttons when appropriate

Steve
Expert Elite Alumnus
Message 3 of 6
Joe-Bouza
in reply to: sboon

Thanks Steve, I'll giver her a look on Monday.
Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People)

HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win10 OS
Message 4 of 6
Joe-Bouza
in reply to: sboon

I checked my alignment super calc and it all looked good and the assembly seems to be reading the SE now.
Next question: what is the correct way to add a 4' shoulder and curbing? I set the shoulder calc to breakover removal on the low side and match slope on the hight side. I used a 4' OutSidesub and thought I should select the lane super in the props, but it matsched the lane cross slope. How do I get it to be 4% at NC?
Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People)

HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win10 OS
Message 5 of 6
Joe-Bouza
in reply to: Joe-Bouza

I hijacke my own thread. You cant. best bet create a transition profile
Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People)

HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win10 OS
Message 6 of 6
Joe-Bouza
in reply to: Joe-Bouza

Make sure the super is calculated
Thank you

Joseph D. Bouza, P.E. (one of 'THOSE' People)

HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram


Note: Its all Resistentialism, so keep calm and carry on

64 Bit Win10 OS

Can't find what you're looking for? Ask the community or share your knowledge.

Post to forums  

Rail Community


Autodesk Design & Make Report