AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
Member
jennifertrice0
Posts: 5
Registered: ‎04-25-2012
Message 1 of 11 (374 Views)

Mouse delay

374 Views, 10 Replies
09-30-2012 10:26 AM

I have a delay when drawing.  I read all the "mouse dely" posts and have tried the following:

1) changed mouse

2) changed graphics setting to basic windows

3) turned off ucs

 

I have a new computer w Acad13.  Any help would be appreciated.  My drawing time is soo slow!

Thank you

*Expert Elite*
antoniovinci
Posts: 1,750
Registered: ‎06-03-2011
Message 2 of 11 (370 Views)

Re: Mouse delay

09-30-2012 10:51 AM in reply to: jennifertrice0

Does this slowness occur with new, empty drawings too..?

Member
jennifertrice0
Posts: 5
Registered: ‎04-25-2012
Message 3 of 11 (367 Views)

Re: Mouse delay

09-30-2012 10:57 AM in reply to: antoniovinci
I just created a new dwg and tested it. It does not have the same delay. -- Jennifer R.Trice, PE Trice, PC 4800 Whitesburg Dr Suite 30-264 Huntsville, AL 35802 Phone: 256 536 0260 Mobile: 256 651 9693 email: jennifertrice@tricepc.com
*Expert Elite*
antoniovinci
Posts: 1,750
Registered: ‎06-03-2011
Message 4 of 11 (337 Views)

Re: Mouse delay

10-01-2012 01:17 AM in reply to: jennifertrice0

Madame,

create a new command icon and paste this macro into:

 

^C^C-PURGE;A;*;N;-PURGE;R;*;N;-PURGE;Z;AUDIT;Y;-SCALELIST;R;Y;;-PURGE;A;*;N;-OVERKILL;ALL;;;FILTERS;

 

then click on the icon: the "slow" drawing will get cleaned and (I hope) will come back to full speed.

*Expert Elite*
jmayo
Posts: 3,002
Registered: ‎11-13-2006
Message 5 of 11 (323 Views)

Re: Mouse delay

10-01-2012 06:48 AM in reply to: jennifertrice0

If  your mouse is behaiving like this while hovering around C3D point objects then go to the CUI and turn off the Rollover Tooltips for Cogo Points.

John Mayo, PE
IDSP 2014
Win 7 64, Xeon ES165@3.2Ghz,
64 GB RAM, Quadro K4000 (x2)
*Expert Elite*
AllenJessup
Posts: 6,100
Registered: ‎05-21-2003
Message 6 of 11 (322 Views)

Re: Mouse delay

10-01-2012 06:52 AM in reply to: jennifertrice0

Try drawing some tightly spaced objects in the new drawing and than copy them a couple of times almost over top of the original to create a tightly packed area of entities. Then see if there is a delay as the cursor passes over the entities. This will give a clue as to whether it's a resource issue of whether the cursor is lagging because of a setting like tooltips or Selectionpreview.

 

Allen

Member
jennifertrice0
Posts: 5
Registered: ‎04-25-2012
Message 7 of 11 (299 Views)

Re: Mouse delay

10-01-2012 07:22 PM in reply to: AllenJessup
I do see a small delay when I pack an area w entities.
*Expert Elite*
AllenJessup
Posts: 6,100
Registered: ‎05-21-2003
Message 8 of 11 (281 Views)

Re: Mouse delay

10-02-2012 05:15 AM in reply to: jennifertrice0

Then one of the variables that cause the cursor to interact with entities and objects. These may include Osnaps, Tooltips, Selection Preview, Rollover Tooltips and others I may not have thought of at this time.

 

I'd suggest disabling all of these and seeing if you still get the lag. If you do, try observing what kind of objects you're over at the time. I've found that cogo points and featurelines are prime culprits.

 

Allen

Distinguished Mentor
castled071049
Posts: 823
Registered: ‎11-15-2005
Message 9 of 11 (272 Views)

Re: Mouse delay

10-02-2012 09:20 AM in reply to: jennifertrice0

Do you have Selection Cycling on? If so, turn that off. It is notorious for causing mouse delays.

Member
DigiWizz
Posts: 4
Registered: ‎07-13-2013
Message 10 of 11 (143 Views)

Re: Mouse delay

07-13-2013 02:59 PM in reply to: antoniovinci

antoniovinci wrote:

Does this slowness occur with new, empty drawings too..?


That's what my mouse does. It is slow and lagging when inside the GUI of any dwg (empty or not). I'm running AutoCAD 2012 - SP2 on WinXP - SP3 with Intel Pentium 4 2.8 and 2 gb ram. 2008 used to run fine but I wanted to take advantage of parametric design. Now I can't even draw a single line without getting frustrated.

 

Please help!!!  :smileyfrustrated:

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are You Going To Be @ AU 2014? Feel free to drop by our AU topic post and share your plans, plug a class that you're teaching, or simply check out who else from the community might be in attendance. Ohh and don't forgot to stop by the Autodesk Help | Learn | Collaborate booths in the Exhibit Hall and meet our community team if you get a chance!