AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
Distinguished Contributor
nostupidquestions
Posts: 469
Registered: ‎11-17-2005
Message 1 of 7 (155 Views)

hatch pattern issue (pattern to solid)

155 Views, 6 Replies
02-27-2014 07:52 AM

i've got a hatch pattern that is the DOT pattern for existing asphalt. it's annotative because i have 2 viewports, one at 20 scale and a detail at 5 scale. for some reason it randomly turns solid in the 5 scale viewport. am i missing something about annotative hatch patterns?

Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2015
*Expert Elite*
Jay_B
Posts: 2,538
Registered: ‎09-15-2010
Message 2 of 7 (148 Views)

Re: hatch pattern issue (pattern to solid)

02-27-2014 08:08 AM in reply to: nostupidquestions

Are "Annoallvisible" and "Annoautoscale" both turned on on lower right of screen?

 

Is it actually being switched to Solid hatch pattern or is it a scale density issue?

Jay

C3D 2014 SP2
Win 7 Professional 64 Bit
Distinguished Contributor
nostupidquestions
Posts: 469
Registered: ‎11-17-2005
Message 3 of 7 (145 Views)

Re: hatch pattern issue (pattern to solid)

02-27-2014 08:10 AM in reply to: Jay_B

it still says it a dot pattern, just showing up solid. this morning it was working fine. both of those toggles are on.

Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2015
Distinguished Contributor
nostupidquestions
Posts: 469
Registered: ‎11-17-2005
Message 4 of 7 (138 Views)

Re: hatch pattern issue (pattern to solid)

02-27-2014 08:24 AM in reply to: nostupidquestions

there are actually two 5 scale viewports. one is dots and the other is solid. frustrating.

Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2015
*Expert Elite*
JoAnn_Hogan
Posts: 528
Registered: ‎06-25-2012
Message 5 of 7 (130 Views)

Re: hatch pattern issue (pattern to solid)

02-27-2014 08:50 AM in reply to: nostupidquestions

Would you mind sharing your drawing so we could have a look at the issue

If this post solved your issue please mark as solved and Kudos are always welcome =)

Jo - Ann (P.S follow me on twitter @JoAnn_Hogan)


AutoCAD Certified Professional 2014 / Inventor Certified Professional 2014
*Expert Elite*
Jay_B
Posts: 2,538
Registered: ‎09-15-2010
Message 6 of 7 (124 Views)

Re: hatch pattern issue (pattern to solid)

02-27-2014 09:03 AM in reply to: nostupidquestions

nostupidquestions wrote:

there are actually two 5 scale viewports. one is dots and the other is solid. frustrating.


Hmm, Try using the "Match Properties" command. Select the edge of the good 5 scale VP then the Bad one.

Jay

C3D 2014 SP2
Win 7 Professional 64 Bit
Distinguished Contributor
nostupidquestions
Posts: 469
Registered: ‎11-17-2005
Message 7 of 7 (98 Views)

Re: hatch pattern issue (pattern to solid)

02-27-2014 11:29 AM in reply to: Jay_B

it's working correctly now. don't know what i did. thanks though.

Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2015
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.