AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
New Member
thorius
Posts: 2
Registered: ‎08-09-2006
Message 1 of 9 (332 Views)

degree of curvature

332 Views, 8 Replies
08-09-2006 06:58 AM
Has anyone figured out to get the degree of curvature (DOC) for a curve in an alignment to be reported for Civil 3D 2007 like was reported in the 2006 version?
*Connie B
Message 2 of 9 (332 Views)

Re: degree of curvature

08-09-2006 11:10 AM in reply to: thorius
Do you need it for highway or railroad curves?

wrote in message news:5263131@discussion.autodesk.com...
Has anyone figured out to get the degree of curvature (DOC) for a curve in
an alignment to be reported for Civil 3D 2007 like was reported in the 2006
version?
New Member
thorius
Posts: 2
Registered: ‎08-09-2006
Message 3 of 9 (332 Views)

Re: degree of curvature

08-09-2006 11:12 AM in reply to: thorius
I need it for highway curves.
Employee
Karen Dowling
Posts: 31
Registered: ‎11-02-2005
Message 4 of 9 (332 Views)

Re: degree of curvature

08-09-2006 11:59 AM in reply to: thorius
You can add an expression to the curve label... see the attached gif file.

Karen Dowling
Autodesk ISD Test Development
Member
petedz
Posts: 4
Registered: ‎10-26-2006
Message 5 of 9 (332 Views)

Re: degree of curvature

10-31-2006 10:40 AM in reply to: thorius
How does one go about getting degree of curvature (D) to display in a label for a PI in C3D 2006?
Contributor
tvlohrman
Posts: 15
Registered: ‎01-04-2007
Message 6 of 9 (332 Views)

Re: degree of curvature

11-05-2008 07:57 AM in reply to: thorius
Ok, but how do I get the radius into this calculation?

Thank you,
Tom
*wfb
Message 7 of 9 (332 Views)

Re: degree of curvature

11-05-2008 09:39 AM in reply to: thorius

One would assume it will get the radius from the
selected curve.

 

Bill

 


style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
Ok,
but how do I get the radius into this calculation? Thank you,
Tom
Contributor
tvlohrman
Posts: 15
Registered: ‎01-04-2007
Message 8 of 9 (332 Views)

Re: degree of curvature

11-05-2008 10:08 AM in reply to: thorius
Radius was not a choice in the expression inset property list. Turns out that I was in the general label styles section, not the Alignment>label sytles>curve section. So, there are different choices available based on what area you are in.
Mentor
JamaL9722060
Posts: 1,312
Registered: ‎04-09-2010
Message 9 of 9 (98 Views)

Re: degree of curvature

08-03-2013 10:45 AM in reply to: Karen Dowling

How to set and label the “degree of curvature”?

 

As the radius of the circular alignment is calculated from the “degree of curvature” (attached) then I couldn’t figure out how to change the default value or to label it (degree of curvature)

 

 

Thank you

 

Best

 

Jamal

----------------------------------------------------------
Jamal NUMAN, GIS and Civil Engineer, MSc
e-mail: JamaL9722060@yahoo.com
P.O.Box: 731, Ramallah, West Bank, Palestine.
----------------------------------------------------------
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.