AutoCAD Civil 3D General Discussion

AutoCAD Civil 3D General Discussion

Reply
Valued Contributor
bozoli
Posts: 51
Registered: ‎02-25-2008
Message 1 of 6 (204 Views)

Created Sheet does not show Vertical Alignment data (Line and Curves)

204 Views, 5 Replies
09-15-2013 01:06 PM

Hi everyone.

 

i  have an issue in with my created sheets that does not show vertical alignment data. everything on the bands shows up nicely but the lines, curves and labels profile are missin.

 

see the attached image. you can notice from the image that there is no a signle data..

 

your help is much appreciated.

 

thanx

*Expert Elite*
Jeff_M
Posts: 4,306
Registered: ‎07-22-2003
Message 2 of 6 (162 Views)

Re: Created Sheet does not show Vertical Alignment data (Line and Curves)

09-15-2013 11:05 PM in reply to: bozoli

Without seeing your drawing, here's a shot in the dark... use the DISPLAY command, then enter P for properties, then D for drawing. Scroll down to the Profile line and be sure the boxes for Model and Plan are checked.

 

If that's not it, you may need to post or email the drawing.

Jeff_M, also a frequent Swamper
Valued Contributor
bozoli
Posts: 51
Registered: ‎02-25-2008
Message 3 of 6 (158 Views)

Re: Created Sheet does not show Vertical Alignment data (Line and Curves)

09-15-2013 11:29 PM in reply to: Jeff_M

hi Jeff,

 

i have went through your suggestion and all my boxes are ticked, but the problem is not solved.

 

the drawing is too big to upload. maybe let me email you the drawing.

 

regards

Silver

 

 

*Expert Elite*
Jeff_M
Posts: 4,306
Registered: ‎07-22-2003
Message 4 of 6 (149 Views)

Re: Created Sheet does not show Vertical Alignment data (Line and Curves)

09-16-2013 05:44 AM in reply to: bozoli

You can email me direct at jeffm AT quuxsoft DOT com although a better option may be to use a Dropbox account and give a link to it.

Jeff_M, also a frequent Swamper
*Expert Elite*
troma
Posts: 2,520
Registered: ‎05-21-2008
Message 5 of 6 (144 Views)

Re: Created Sheet does not show Vertical Alignment data (Line and Curves)

09-16-2013 06:13 AM in reply to: bozoli

Have you tried:

Check the profile style is turned on?

All layers on and thawed?

REGENALL?
Close the drawing and reopen?
Recover the drawing?
Audit the drawing?
Close the program and start it again?
Shut down the machine and reboot?


Credit where credit is due! Give kudos or accept as solution whenever you can.

Valued Contributor
bozoli
Posts: 51
Registered: ‎02-25-2008
Message 6 of 6 (133 Views)

Re: Created Sheet does not show Vertical Alignment data (Line and Curves)

09-16-2013 08:59 AM in reply to: troma

Hi Guys,

 

i now think i know what the problem is, even if i donnot know the solution to it. the problem is i get this when my Profile View have other alignment superimposed. Because when i delete the superimposed profile and creating sheets, then it works fine, but when i create sheets with superimposed profiles, then it gives me this problem.

 

Does anyone know how can i get my left and right offset level that has a different road widths without the option of superimposed profiles?

 

regards

 

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.