AutoCAD Architecture General Discussion

AutoCAD Architecture General Discussion

Reply
Product Support
MichaelBussiere2
Posts: 365
Registered: ‎11-09-2009
Message 1 of 5 (1,911 Views)
Accepted Solution

3DConnexion Devices

1911 Views, 4 Replies
10-03-2012 09:37 AM

ACAD 2013 Device communication Issue:

 

Users see issues with the following;

  • Zoom speed varies in perspective view
  • Pivot point position is far from the model causing the model to go off the drawing area when rotated
  • High zoom out speed after zooming in a small area of the drawing

 



Michael Bussiere II
Support Specialist
Product Support
Autodesk, Inc.
Product Support
MichaelBussiere2
Posts: 365
Registered: ‎11-09-2009
Message 2 of 5 (1,908 Views)

Re: 3DConnexion Devices

10-03-2012 09:39 AM in reply to: MichaelBussiere2

Autodesk 3Dconnexion Hotfix

Download: http://usa.autodesk.com/adsk/servlet/ps/dl/item?siteID=123112&id=20605633&linkID=9240618 

 

This hotfix corrects the following issues with 3Dconnexion devices:

  • Zoom speed varies in perspective view
  • Pivot point position is far from the model causing the model to go off the drawing area when rotated
  • High zoom out speed after zooming in a small area of the drawing

Consult the readme file for installation instructions and more details on the primary issues resolved by this update. Be sure to install the correct hotfix (32-bit or 64-bit) for your software and operating system.

Note: Before applying this hotfix to your Autodesk product, youmust install service pack 1-below (or SP1.1 for AutoCAD and AutoCAD LT).

ACA2013 Update 1: http://usa.autodesk.com/adsk/servlet/ps/dl/item?siteID=123112&id=20556359&linkID=9240658



Michael Bussiere II
Support Specialist
Product Support
Autodesk, Inc.
Active Member
stensq
Posts: 7
Registered: ‎10-09-2009
Message 3 of 5 (1,879 Views)

Re: 3DConnexion Devices

10-05-2012 03:32 AM in reply to: MichaelBussiere2

Will this Hotfix work with Autocad Architecture 2012?

Product Support
MichaelBussiere2
Posts: 365
Registered: ‎11-09-2009
Message 4 of 5 (1,873 Views)

Re: 3DConnexion Devices

10-05-2012 07:17 AM in reply to: MichaelBussiere2

This will work with the following products,

 

Applies to:
AutoCAD® 2013
AutoCAD® Architecture 2013
AutoCAD® Civil 3D® 2013
AutoCAD® Electrical 2013
AutoCAD LT® 2013
AutoCAD® Map 3D 2013
AutoCAD® Mechanical 2013
AutoCAD® MEP 2013
AutoCAD® P&ID 2013
AutoCAD® Plant 3D 2013
AutoCAD® Raster Design 2013
AutoCAD® Structural Detailing 2013
AutoCAD® Utility Design 2013



Michael Bussiere II
Support Specialist
Product Support
Autodesk, Inc.
Member
DGArch
Posts: 3
Registered: ‎12-16-2010
Message 5 of 5 (262 Views)

Re: 3DConnexion Devices

05-20-2014 02:15 PM in reply to: MichaelBussiere2

Zoom is too fast in constrained orbit mode, and too slow in walk mode (AutoCad Architecture 2009) is there a fix for this, or has this issue been remedied in later versions?

 

On a separate (somewhat related) topic, I can't edit (very easily, if at all) 3D models while in perspective view- has this issue been remedied in a newer version of Architecture?

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.